NAMZ Catalogue

PRODUCT CATALOG - V1.2020

1999

2019

NAMZ Custom Cycle Products

PROVIDING YOU 20-YEARS OF ELECTRICAL EXCELLENCE! HELPFUL INFORMATION

As I sit here and type this, it is hard to believe that we’ve been at it for over 20-years now! There have been so many trends that have come and gone and even come back again, but one thing is for sure, everyone here at NAMZ prides themselves in providing YOU with the very best products and service. Whether you are a new customer or have been using our products for years, the message remains the same. We want to be “the” one stop shop, the industry’s best source for electrical connectors, wiring harnesses, installation supplies, Badlands modules and LED lighting! Without you, our loyal customers, we wouldn’t be here, so here’s to YOU, Happy 20- Year Anniversary to us, both! May we continue to be along with you for the next 20-years, rubber side down. JZ Ÿ ALL NAMZ electrical products including harnesses, pigtails and modules, including Badlands Modules are MADE IN THE USA! That’s right, we make them right here in Pennsylvania, 5-days a week. That’s why we can offer YOU a LIFETIME warranty on many items.

Badlands Basic Color Codes

Ÿ Black: Ÿ Red: Ÿ Blue: Ÿ Orange:

GROUND BRAKE

Brown: Violet: Yellow: Gray:

RIGHT TURN SIGNAL LEFT TURN SIGNAL

RIGHT RUN-BRAKE-TURN output to rear turn signal LEFT RUN-BRAKE-TURN output to rear turn signal

RUNNING LIGHT

FUSED 12+

Badlands Module Family (founded in 1990) All Badlands Modules EXCEPT for LE-01 & LE-02 have a LIFETIME warranty!

Fun Fact: Do you know the fastest and easiest way to fish wires through handlebars or a frame? The inside of a speedometer cable, yes, this spring-steel cable is AWESOME when fishing wires. Simply remove the cable from an old or new speedo cable, tape on your wiring and have at it! Fun Fact: Did you know that we sell over 20,000 Badlands modules a year? That is a lot of modules for sure and we also provide support for each one as well. Every once and a while, we get one sent back claiming to be defective when in reality, it wasn’t hooked up properly. But that’s what we’re here for, and the instructions are on our website! Each year, we average less than 6 ten-thousandth of a percent “defective”, that’s less than (12-modules) for every 20,000 sold! Ÿ ATS or Automatic Turn Signal Canceller: (All modules with ATS- prefix) These OEM style replacement or custom flashing modules provide self-canceling turn signals that last for 11-seconds before shutting off. Ÿ Brake Light Eliminator : (All modules with IHL-04 prefix) These modules were designed for ALL CAN/Bus models without a center taillight. The factory added the brake light function onto the high-filliment rear left and right turn signals preventing customers to use AMBER turn signals, tow a five wire trailer or even using center taillights with built-in turn signals. Ÿ Illuminator: (All modules with ILL- prefix) These are the industry’s first RUN-BRAKE-TURN signal modules with built-in Load Equalizer . If you want to convert your rear AMBER only turn signals to having RED running light, brake light and turn signal functions, this is your module. The load equalizer will prevent rapid flashing signals when changing bulbs over to LED’s. Ÿ Intensifier: (IHL-01, IHL-02 & IHL-03 prefix) These modules are intended to provide dual functions to a single function light. If you have a turn signal or taillight with (1) power wire, the IHL-01 will convert the light to high/low functions, (run/brake). The IHL-02 is designed for (2) single power wire lights and the compact IHL-03 will only work on a pair of LED’s no more than 500-milliamps per side. Ÿ Load Equalizer: (All modules with LE- prefix) These modules is where it all started back in 1990. The “originals” of preventing rapid flashing turn signals when converting to non-OEM bulbs or LED’s. Load equalizers simply match the amperage stock/OEM TSM or TSSM’s are looking for from a stock bulb, telling the bike all is okay. Ÿ Dynamic & Static Sequential Illuminator: These “industry first” modules provide sequential flashing turn signals on (3) LED’s left and (3) LED’s right when activated. They also provide running light and brake light functions with a built-in Load Equalizer. On the Dynamic version, each of the (3) LED’s will flash on then off before starting the sequence over again. On the Static version, each of the (3) LED’s will light and stay on before all (3) shut off and restart the sequence over again. Can use ANY LED you wish but they must be RED. Ÿ PRO-III: This “all-in-one” Illuminator module was intended for custom motorcycles or when performing a complete re-wire. It provides 11-second self-canceling turn signal functions, front left and right turn signal output (1 wire per side) has running light and turn signal functions, rear left and right turn signal output (1 wire per side) has running light, brake light and turn signal functions and there are left and right turn signal indicator wires for dash/instrument cluster.

CONTENT The most complete listing of electrical components all in one place.

Wiring Extension Kits

Connectors & Terminals

p.2

p.34

p.50 Braided Hoses & Clamps Brass, Copper & Stainless Steel oil and fuel hoses are sold in 25-foot spools. Clamps are polished natural brass, chrome or powder coated black, copper and silver in 1/4”-5/16” and 3/8” sizes. Sold in 6-packs. Handlebar switch harnesses, throttle- by-wire harnesses, heated grip and oxygen sensors. If there is a need for an extension, we have it. All of our terminals are crimped on by mil-spec crimping presses for a perfect fit.

American or Metric, you’ll find them all in this section. Brand names like AMP/TE, Deutsch, Molex, JST, JAE and Sumitomo. NAMZ also carries all of the mating male and female terminals, including wire seals.

Wiring Harnesses & Kits

p.42

CAN/Bus, replacement OEM ignition harnesses, power ports, y-adaptors, LED headlight harnesses or tour- pack harnesses. Most of our harnesses are 100% plug-n-play for an easy installation.

Wire Braiding Kits

Badlands Modules

p.51

p.52

Stainless steel, 100% brass or natural copper, our braided harnesses or do it yourself kits help create that custom look. Easy to cut, easy to install and the clear heat shrink protects your ride. p.66 Trailer Isolators - Off Road We offer trailer isolators for just about every make and model motorcycle. Available in 4 or 5 wire systems based on your trailer’s design. The ever growing UTV market was in need of some NAMZ love so we have started a collection of must haves!

Badlands, the original lighting module company since 1990! The complete line with many new Plug-n-Play versions. We also offer CAN/Bus switch controllers, momentary switch convertors and trailer isolators for most makes and models.

Tools & Supplies

p.69

Crimp & removal tools, O2 bungs, red, blue and yellow terminals, fork, ring or quick disconnect, they’re all here. Wire, fuses, circuit breakers, headlamp sockets, adaptors, terminals, relays and sockets, push buttons, switches and audio supplies.

NAMZ CCP Inc. / Table of Contents

1

AMP / TE CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS MULTILOCK

CONNECTORS

NA-174463-2

The AMP Multilock Series has been used on all factory motorcycles since 1996 and are still used today. They are small, compact connectors available in many cavity sizes. You will find these connectors on rear fender harnesses, front and rear turn signals, heated grip wiring, older main harness and speedometer connections.

2-POSITION FEMALE PLUG

Requires (2) FEMALE terminals. OEM PART NUMBER: 73152-96BK

NA-174460-2

NA-174921-2

2-POSITION MALE CAP

3-POSITION FEMALE PLUG

Requires (2) MALE terminals. OEM PART NUMBER: 73102-96BK

Requires (3) FEMALE terminals. OEM PART NUMBER: 73153-96BK

NA-174928-2

NA-174922-2

4-POSITION FEMALE PLUG OEM PART NUMBER: 73154-96BK Requires (4) FEMALE terminals.

3-POSITION MALE CAP OEM PART NUMBER: 73103-96BK Requires (3) MALE terminals.

NA-174929-2

NA-174923-2

4-POSITION MALE CAP OEM PART NUMBER: 73104-96BK Requires (4) MALE terminals.

6-POSITION FEMALE PLUG OEM PART NUMBER: 73156-96BK Requires (6) FEMALE terminals.

NA-174930-2

NA-173850-2

6-POSITION MALE CAP OEM PART NUMBER: 73106-96BK Requires (6) MALE terminals.

8-POSITION FEMALE PLUG

Requires (8) FEMALE terminals. OEM PART NUMBER: 73158-96BK

NAMZ CCP Inc. / AMP-TE

2

CONNECTORS

AMP / TE CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

NA-174931-2

NA-174465-2

8-POSITION MALE CAP

10-POSITION FEMALE PLUG OEM PART NUMBER: 73160-96BK Requires (10) FEMALE terminals.

Requires (8) MALE terminals. OEM PART NUMBER: 73108-96BK

NA-174932-2

NA-173851-2

10-POSITION MALE CAP OEM PART NUMBER: 73110-96BK Requires (10) MALE terminals.

12-POSITION FEMALE PLUG OEM PART NUMBER: 73164-96BK Requires (12) FEMALE terminals.

NA-174933-2

NA-173631-1

100-PACK, FEMALE TERMINALS OEM PART NUMBER: 73191-96 CRIMP TOOL: NDC-990170

12-POSITION MALE CAP OEM PART NUMBER: 73112-96BK Requires (12) MALE terminals.

NA-173645-1

NAC-BKO

100-PACK, MALE TERMINALS OEM PART NUMBER: 73190-96 CRIMP TOOL: NDC-990170

MULTILOCK BUILDERS KIT Kit includes (8) 2, 3, 4, 6, and 8- position PLUG and CAP connectors with (100) male & female terminals.

NA-174056-2

NA-174057-2

2-POSITION FEMALE PLUG (040)

2-POSITION MALE CAP (040)

Requires (2) FEMALE (040) Series terminals. OEM PART NUMBER: 72912-01BK

Requires (2) MALE (040) Series terminals. OEM PART NUMBER: 72902-01BK

NAMZ CCP Inc. / AMP-TE

3

AMP / TE CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

CONNECTORS

NA-174966-2

NA-174967-2

4-POSITION FEMALE PLUG OEM PART NUMBER: 72914-01BK Requires (2) FEMALE (040) Series terminals.

4-POSITION MALE CAP (040)

Requires (2) MALE (040) Series terminals. OEM PART NUMBER: 72904-01BK

NA-175062-1

NA-175063-1

25-PK, FEMALE (040) TERMINALS OEM PART NUMBER: 72991-01 CRIMP TOOL: NDC-990170

25-PK, MALE (040) TERMINALS

CRIMP TOOL: NDC-990170 OEM PART NUMBER: 72990-01

MATENLOCK

NA-350777-1

The AMP Matenlock Series is a popular connector in the aftermarket, used on many of the smaller production motorcycle manufacturers like Indian, Pure Steel, Swift and Titan. These white connectors are watertight and come packaged with the mating wire and/or interface seal for convenience. Easy to use, many cavity options available.

2-POSITION FEMALE PLUG KIT: Includes wire & interface seals. Requires (2) FEMALE terminals.

NA-350778-1

NA-350766-1

2-POSITION MALE CAP

3-POSITION FEMALE PLUG KIT: Includes wire & interface seals. Requires (3) FEMALE terminals.

Requires (2) MALE terminals. KIT: Includes wire seal.

NA-350767-1

NA-350779-1

3-POSITION MALE CAP KIT: Includes wire seal. Requires (3) MALE terminals.

4-POSITION FEMALE PLUG KIT: Includes wire & interface seals. Requires (4) FEMALE terminals.

NAMZ CCP Inc. / AMP-TE

4

CONNECTORS

AMP / TE CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

NA-350780-1

NA-350715-1

4-POSITION MALE CAP KIT: Includes wire seal. Requires (4) MALE terminals.

6-POSITION FEMALE PLUG Requires (6) FEMALE terminals. KIT: Includes wire & interface seals.

NA-350781-1

NA-350720-1

6-POSITION MALE CAP KIT: Includes wire seal. Requires (6) MALE terminals.

9-POSITION FEMALE PLUG KIT: Includes wire & interface seals. Requires (9) FEMALE terminals.

NA-350782-1

NA-350735-1

12-POSITION FEMALE PLUG KIT: Includes wire & interface seals. Requires (12) FEMALE terminals.

9-POSITION MALE CAP KIT: Includes wire seal. Requires (9) MALE terminals.

NA-350783-1

NA-350736-1

12-POSITION MALE CAP KIT: Includes wire seal. Requires (12) MALE terminals.

15-POSITION FEMALE PLUG Requires (15) FEMALE terminals. KIT: Includes wire & interface seals.

NA-350784-1

NA-350536-1

15-POSITION MALE CAP

100-PACK, FEMALE SOCKETS

Requires (15) MALE terminals. KIT: Includes wire seal.

CRIMP TOOL: NDC-990170 MATENLOCK female terminals.

NAMZ CCP Inc. / AMP-TE

5

TERMINALS - WIRE SEALS - BUILDERS KITS AMP / TE CONNECTORS

CONNECTORS

NA-350218-1 100-PACK, MALE PINS

NAC-BKA

MATENLOCK BUILDERS KIT Kit includes (6) 2 & 12, (8) 6 & 9, and (4) 3 & 4-position PLUG and CAP connectors with (100) male & female terminals.

MATENLOCK male terminals. CRIMP TOOL: NDC-990170

OEM MATENLOCK

NA-1-480349-0

This series of connectors and terminals has been used between 1971 and 1995 on most OEM HD models. A very simple to use connection system, these OEM Matenlock’s are perfect when servicing or restoring the original look of an early model, without sacrificing quality. Available in 1 to 12-position male and female connectors with stamped terminals.

1-POSITION FEMALE OEM PART NUMBER: 72043-71A Requires (1) FEMALE terminal.

NA-1-480350-0 1-POSITION MALE OEM PART NUMBER: 72044-71A Requires (1) MALE terminal.

NA-1-480318-0

2-POSITION FEMALE OEM PART NUMBER: 72034-71 Requires (2) FEMALE terminal.

NA-1-480319-0 2-POSITION MALE OEM PART NUMBER: 72035-71 Requires (2) MALE terminals.

NA-1-480303-0

3-POSITION FEMALE Requires (3) FEMALE terminals. OEM PART NUMBER: 72036-71

NA-1-480305-0

NA-1-480424-0

3-POSITION MALE

4-POSITION FEMALE OEM PART NUMBER: 70292-89 Requires (4) FEMALE terminals.

Requires (3) MALE terminals. OEM PART NUMBER: 72040-71

NAMZ CCP Inc. / AMP-TE

6

CONNECTORS

AMP / TE CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

NA-1-480426-0

NA-1-480270-0

4-POSITION MALE OEM PART NUMBER: 70291-89 Requires (4) MALE terminals.

6-POSITION FEMALE OEM PART NUMBER: 72037-71 Requires (6) FEMALE terminals.

NA-1-480340-0

NA-1-480283-0

6-POSITION MALE OEM PART NUMBER: 72041-71 Requires (6) MALE terminals.

8-POSITION FEMALE Requires (8) FEMALE terminals. OEM PART NUMBER: 70287-81A

NA-1-480345-0

NA-1-480285-0

10-POSITION FEMALE OEM PART NUMBER: 70293-87A Requires (10) FEMALE terminals.

8-POSITION MALE OEM PART NUMBER: 70288-81 Requires (8) MALE terminals.

NA-1-480339-0

NA-1-480287-0

10-POSITION MALE Requires (10) MALE terminals. OEM PART NUMBER: 70305-90

12-POSITION FEMALE Requires (12) FEMALE terminals. OEM PART NUMBER: 72278-74

NA-1-480288-0

NA-61314-1

12-POSITION MALE Requires (12) MALE terminals. OEM PART NUMBER: 72276-74

100-PK, OEM FEMALE SOCKETS OEM PART NUMBER: 72038-71A CRIMP TOOL: NDC-990170

NAMZ CCP Inc. / AMP-TE

7

AMP / TE / DELPHI TERMINALS - WIRE SEALS - BUILDERS KITS

CONNECTORS

NA-61116-1 100-PK, OEM MALE PINS OEM PART NUMBER: 72039-71A CRIMP TOOL: NDC-990170

NTBW-CK

KIT

7-POSITION MALE & FEMALE Throttle-by-wire MCL male & female connectors with terminals. We recommend using our crimp tool NJC- 990120 for a perfect crimp every time.

NA-282080-1 2-POSITION FEMALE PLUG OEM PART NUMBER: 72007-05 KIT: Includes wire seals & terminals. USE: O2 Sensors

NA-282089-1 5-POSITION FEMALE PLUG OEM PART NUMBER: 72012-07 USE: Active Exhaust Sensor KIT: Includes wire seals & terminals.

NA-1-1355668-2 2-POSITION FEMALE PLUG

NA-2-1355668-2 2-POSITION FEMALE PLUG

KIT: Includes wire seals & terminals. OEM PART NUMBER: 72450-01 USE: V-Rod Headlamp Connector

USE: V-Rod Headlamp Connector KIT: Includes wire seals & terminals. OEM PART NUMBER: 72449-01

NMCON-03P 3-POSITION FEMALE PLUG

NMCON-03R 3-POSITION MALE PLUG

USE: ‘17-Up FXST Rear Fender OEM PART NUMBER: 69201613 KIT: Includes wire seals & terminals.

USE: ‘17-Up FXST Rear Fender KIT: Includes wire seals & terminals. OEM PART NUMBER: 69201406

DELPHI NAMZ has the most complete collection of Delphi EFI and component connectors in the industry. NAMZ is the only supplier where you can find mating connectors for many of them! All of our Delphi connectors come with terminals, TPA locks and wire seals for easy installation. OEM part numbers are provided for quick reference. 8

ND-15336027-B 2-POSITION FEMALE PLUG OEM PART NUMBER: 72062-06 USE: Air Temp Sensor KIT: Includes wire seals & terminals.

NAMZ CCP Inc. / AMP-TE / DELPHI

CONNECTORS

DELPHI CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

ND-15336029-B

ND-13532244 3-POSITION FEMALE PLUG OEM PART NUMBER: 72065-06A KIT: Includes wire seals & terminals. USE: TPS Sensor

3-POSITION FEMALE PLUG

USE: Speed Sensor & Alarm KIT: Includes wire seals & terminals. OEM PART NUMBER: 72064-06

ND-15354716-B

ND-12129946-B

4-POSITION FEMALE PLUG

3-POSITION FEMALE PLUG OEM PART NUMBER: 72230-98 KIT: Wire seals, terminals & TPA. USE: Map Sensor

KIT: Includes wire seals & terminals. OEM PART NUMBER: 72066-06A USE: Idle Speed, Coil & Fuel Pump.

ND-12129142-B

ND-15419715

2-POSITION FEMALE PLUG

2-POSITION FEMALE PLUG OEM PART NUMBER: 72098-06 USE: Fuel Injector KIT: Wire seals, terminals & TPA.

OEM PART NUMBER: 72244-95 USE: Fuel Injector

KIT: Includes terminals.

ND-12162215-B

ND-12162193-B

2-POSITION FEMALE PLUG OEM PART NUMBER: 72273-95 USE: Engine Temp Sensor KIT: Includes terminals.

2-POSITION FEMALE PLUG OEM PART NUMBER: 72247-95

USE: Air Temp Sensor KIT: Includes terminals.

ND-12162182-B

ND-12162191-B

3-POSITION FEMALE PLUG OEM PART NUMBER: 72280-95 USE: TPS Sensor KIT: Includes terminals.

4-POSITION FEMALE PLUG OEM PART NUMBER: 72263-95 USE: Idle Speed & Ignition Coil KIT: Includes terminals.

NAMZ CCP Inc. / DELPHI

9

NAMZ CCP Inc. / DELPHI

DELPHI CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

CONNECTORS

ND-12065298

ND-12129387 1-POSITION FEMALE PLUG OEM PART NUMBER: 72350-11 KIT: Includes wire seal & terminals. USE: BCM Power

4-POSITION FEMALE PLUG

USE: Oil Pressure Switch OEM PART NUMBER: 74438-99 KIT: Wire seals, terminals & TPA.

NA-1-488533-6

ND-FBP

18-POSITION FEMALE PLUG

1-POSITION FEMALE PLUG, 5PK OEM PART NUMBER: 72260-04 USE: Accessory power. KIT: 5PK, includes terminals.

USE: BCM Connector OEM PART NUMBER: 72664-12 KIT: Includes terminals.

ND-MBP

ND-12077591

1-POSITION MALE PLUG, 5PK

5-POSITION FEMALE PLUG USE: ‘14-Up Tour Pack Connector OEM PART NUMBER: 69200225 KIT: Includes wire seal & terminals.

KIT: 5PK, includes terminals. OEM PART NUMBER: 72100-04 USE: Accessory power.

ND-15397577

NHD-69200193

MULTI-POSITION FEMALE PLUG OEM PART NUMBER: 69200193 USE: ‘14-Up Radio & BCM KIT: Includes 3-sizes of terminals.

6-POSITION FEMALE PLUG OEM PART NUMBER: 69201394 USE: ‘17-Up M8 Throttle Control KIT: Includes wire seal & terminals.

NHD-72130-04

NHD-72485-07

12-POSITION FEMALE PLUG

4-POSITION FEMALE PLUG OEM PART NUMBER: 72485-07 USE: ‘07-Up Fuel Pump Connector KIT: Includes wire seal & terminals.

KIT: Includes wire seal & terminals. OEM PART NUMBER: 72130-04 USE: ‘04-Up Speedo & Tri-Bar Light

NAMZ CCP Inc. / DELPHI

10

CONNECTORS

DELPHI CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

NMD-410016 3-POSITION MALE PLUG MATES WITH: OEM # 72064-06 KIT: Includes wire seal & terminals. USE: Speed Sensor/Siren MATE.

NMD-410027 3-POSITION MALE PLUG

KIT: Includes wire seal & terminals. MATES WITH: OEM # 72065-06 USE: TPS Sensor MATE.

NMD-410017 4-POSITION MALE PLUG

NMD-410001 4-POSITION MALE PLUG MATES WITH: OEM # 72230-98 USE: Map Sensor MATE. KIT: Wire seals, terminals & TPA.

USE: Fuel Pump & Coil MATE. MATES WITH: OEM # 72066-06 KIT: Includes wire seal & terminals.

NMD-109076 2-POSITION ADAPTER PLUG MATES WITH: OEM # 72098-06 and converts to OEM # 72244-95. KIT: No terminals needed.

NMD-109077 2-POSITION ADAPTER PLUG MATES WITH: OEM # 72244-95 and converts to OEM # 72098-06. KIT: No terminals needed.

NDP-ABK EFI & COMPONENT BUILDERS KIT Kit includes an assortment of EFI, Component, Exhaust and O2 Sensor connectors with all needed wire seals and terminals. Perfect for any shop!

NHD-72078-00 ECM 36 PIN CONNECTOR KIT EFI Models: 2002-2011 (HD# 72078- 00) Connector, Strain Relief, retainer lock, Seal, Zip-Tie, Terminals.

WEATHER PACK

NDP-38061

The Delphi Weather Pack Series is an environmentally sealed connection system, made to withstand exposure to extreme temperatures, moisture and chemicals with superior performance. They are a less expensive alternative than other watertight connectors, although they are larger in size. Terminals will accommodate #16-#18 wire sizes. NAMZ CCP Inc. / DELPHI

1-POSITION FEMALE CONNECTOR KIT: Includes wire seal. Requires (1) FEMALE terminal.

11

NAMZ CCP Inc. / DELPHI

DELPHI CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

CONNECTORS

NDP-38060

NDP-38063

1-POSITION MALE CONNECTOR

2-POSITION FEMALE CONNECTOR

Requires (1) MALE terminal. KIT: Includes wire seal.

Requires (2) FEMALE terminals. KIT: Includes wire seals.

NDP-38062

NDP-38065

3-POSITION FEMALE CONNECTOR KIT: Includes wire seals. Requires (3) FEMALE terminals.

2-POSITION MALE CONNECTOR KIT: Includes wire seals. Requires (2) MALE terminals.

NDP-38064

NDP-38069

5-POSITION FEMALE CONNECTOR KIT: Includes wire seals. Requires (5) FEMALE terminals.

3-POSITION MALE CONNECTOR

Requires (3) MALE terminals. KIT: Includes wire seals.

NDP-38068

NDP-30037 50-PACK, FEMALE TERMINALS WEATHER PACK female terminals. CRIMP TOOL: NDC-990170

5-POSITION MALE CONNECTOR

Requires (5) MALE terminals. KIT: Includes wire seals.

NDP-30036 50-PACK, MALE TERMINALS WEATHER PACK male terminals. CRIMP TOOL: NDC-990170

NDP-39000

10-PACK, WIRE SEALS WEATHER PACK wire seals. KIT: 10-Pack of replacement seals.

NAMZ CCP Inc. / DELPHI

12

CONNECTORS

DELPHI CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

DELPHI PIGTAILS

PT-12129142-B

The Delphi pigtail concept was born when a customer emailed us and said that having EFI and component connectors pre-wired as pigtails, with OEM color matching wire, would be awesome. Why not, a MIL SPEC machine crimp, matching wire colors and ready to install, it doesn’t get any easier! The end of the wire is stripped but the jacket is left to prevent wire fraying.

FUEL INJECTOR PIGTAIL OEM connector # 72244-95 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

PT-12129946-B

PT-12162182-B

THROTTLE POSITION PIGTAIL OEM connector # 72280-95 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

MAP SENSOR PIGTAIL

OEM connector # 72230-98 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

PT-12162191-B

PT-12162193-B

IDLE SPEED & COIL PIGTAIL

ENGINE TEMP PIGTAIL OEM connector # 72273-95 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

OEM connector # 72263-95 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

PT-12162215-B

PT-13532244 THROTTLE POSITION PIGTAIL OEM connector # 72065-06A with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

INTAKE AIR TEMP PIGTAIL OEM connector # 72247-95 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

PT-15336027-B

PT-15336029-B

SPEED SENSOR/ALARM PIGTAIL OEM connector # 72064-06 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

AIR INTAKE PIGTAIL OEM connector # 72062-06 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

NAMZ CCP Inc. / DELPHI

13

NAMZ CCP Inc. / DELPHI

DELPHI / DEUTSCH CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

CONNECTORS

PT-15354716-B

PT-15419715

IGNITION COIL/IDLE AIR PIGTAIL OEM connector # 72066-06A with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

FUEL INJECTOR PIGTAIL OEM connector # 72098-06 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

PT-410001

PT-410016

MATE TO SPEED/SIREN PIGTAIL OEM connector # 72064-06 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

MATE TO MAP SENSOR PIGTAIL Mates to OEM connector # 72230-98 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

PT-410017

PT-410027

MATE TO IGNITION COIL PIGTAIL OEM connector # 72066-06 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

MATE TO TPS SENSOR PIGTAIL OEM connector # 72065-06 with color matching 15” long wire crimped and installed. Wires are stripped with slug left on and comes with 3/16” heat shrink.

DEUTSCH DT

DP-2G 2-POSITION FEMALE PLUG OEM PART NUMBER: 72132-94GY KIT: Includes wedge lock only.

NAMZ is proud to be the LARGEST provider of Deutsch Connectors, terminals and hand tools in the industry. One of the easiest connectors to service, watertight and found on OEM models since 1994 through current models. Available in GRAY or BLACK, 2 through 12-position male and female gender. Solid terminals or stamped available.

DR-2G

DP-3G

2-POSITION MALE RECEPTACLE OEM PART NUMBER: 72122-94GY KIT: Includes wedge lock only.

3-POSITION FEMALE PLUG OEM PART NUMBER: 72133-94GY KIT: Includes wedge lock only.

NAMZ CCP Inc. / DELPHI / DEUTSCH

14

CONNECTORS

TERMINALS - WIRE SEALS - BUILDERS KITS DEUTSCH CONNECTORS

DR-3G

DP-4G

3-POSITION MALE RECEPTACLE

4-POSITION FEMALE PLUG

KIT: Includes wedge lock only. OEM PART NUMBER: 72123-94GY

KIT: Includes wedge lock only. OEM PART NUMBER: 72134-94GY

DR-4G

DP-6G

6-POSITION FEMALE PLUG OEM PART NUMBER: 72136-94GY KIT: Includes wedge lock only.

4-POSITION MALE RECEPTACLE OEM PART NUMBER: 72124-94GY KIT: Includes wedge lock only.

DR-6G

DP-8G

6-POSITION MALE RECEPTACLE OEM PART NUMBER: 72126-94GY KIT: Includes wedge lock only.

8-POSITION FEMALE PLUG

KIT: Includes wedge lock only. OEM PART NUMBER: 72138-94GY

DR-8G

DP-12G 12-POSITION FEMALE PLUG KIT: Includes wedge lock only. OEM PART NUMBER: 72139-94GY

8-POSITION MALE RECEPTACLE

KIT: Includes wedge lock only. OEM PART NUMBER: 72128-94GY

DR-12G

DP-2B

12-POSITION MALE RECEPTACLE

2-POSITION FEMALE PLUG

KIT: Includes wedge lock only. OEM PART NUMBER: 72129-94GY

KIT: Includes wedge lock only. OEM PART NUMBER: 72112-94BK

NAMZ CCP Inc. / DEUTSCH

15

NAMZ CCP Inc. / DELPHI

TERMINALS - WIRE SEALS - BUILDERS KITS DEUTSCH CONNECTORS

CONNECTORS

DR-2B

DP-3B

2-POSITION MALE RECEPTACLE

3-POSITION FEMALE PLUG OEM PART NUMBER: 72133-94BK KIT: Includes wedge lock only.

KIT: Includes wedge lock only. OEM PART NUMBER: 72102-94BK

DR-3B

DP-4B

4-POSITION FEMALE PLUG

3-POSITION MALE RECEPTACLE OEM PART NUMBER: 72103-94BK KIT: Includes wedge lock only.

KIT: Includes wedge lock only. OEM PART NUMBER: 72114-94BK

DR-4B

DP-6B

4-POSITION MALE RECEPTACLE OEM PART NUMBER: 72104-94BK KIT: Includes wedge lock only.

6-POSITION FEMALE PLUG OEM PART NUMBER: 72116-94BK KIT: Includes wedge lock only.

DR-6B

DP-8B 8-POSITION FEMALE PLUG OEM PART NUMBER: 72118-94BK KIT: Includes wedge lock only.

6-POSITION MALE RECEPTACLE

KIT: Includes wedge lock only. OEM PART NUMBER: 72106-94BK

DR-8B

DP-12B

8-POSITION MALE RECEPTACLE OEM PART NUMBER: 72108-94BK KIT: Includes wedge lock only.

12-POSITION FEMALE PLUG OEM PART NUMBER: 72119-94BK KIT: Includes wedge lock only.

NAMZ CCP Inc. / DEUTSCH

16

CONNECTORS

DEUTSCH CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

DR-12B

STAMPED SOCKETS

12-POSITION MALE RECEPTACLE

100-PACK, FEMALE SOCKETS OEM PART NUMBER: 72191-94 CRIMP TOOL: DSCT-02

KIT: Includes wedge lock only. OEM PART NUMBER: 72109-94BK

STAMPED PINS

SOLID SOCKETS

100-PACK, FEMALE SOCKETS

100-PACK, MALE TERMINALS OEM PART NUMBER: 72190-94 CRIMP TOOL: DSCT-02

CRIMP TOOL: DPCT-01 OEM PART NUMBER: 72193-98

DT-HP

SOLID PINS

100-PACK, MALE TERMINALS

10-PACK, HOLE PLUGS

CRIMP TOOL: DPCT-01 OEM PART NUMBER: 72192-98/R

USE: DT Series only. OEM PART NUMBER: 72195-94

NDC-BKG DEUTSCH GRAY BUILDERS KIT Kit includes (8) 2, 3, 4, 6, and 8- position PLUG and CAP connectors with (100) male & female terminals.

NDC-BKB DEUTSCH BLACK BUILDERS KIT Kit includes (8) 2, 3, 4, 6, and 8- position PLUG and CAP connectors with (100) male & female terminals.

DEUTSCH DTM These smaller versions of the original Deutsch DT Series, were first used back in 1998 and are just as reliable and serviceable as the larger version. Available in 2 through 12-positions, male and female mates and black in color. Our DTM connectors come with wedge locks and stamped terminals for easy installation. Hole plugs are available separately. NAMZ CCP Inc. / DEUTSCH

MDP-2B 2-POSITION FEMALE PLUG

OEM PART NUMBER: 74112-98BK KIT: Includes wedge lock & terminals.

17

NAMZ CCP Inc. / DELPHI

DEUTSCH CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

CONNECTORS

MDR-2B 2-POSITION MALE RECEPTACLE OEM PART NUMBER: 74102-98BK KIT: Includes wedge lock & terminals.

MDP-3B 3-POSITION FEMALE PLUG

OEM PART NUMBER: 74113-98BK KIT: Includes wedge lock & terminals.

MDP-4B 4-POSITION FEMALE PLUG

MDR-3B 3-POSITION MALE RECEPTACLE KIT: Includes wedge lock & terminals. OEM PART NUMBER: 74103-98BK

OEM PART NUMBER: 74114-98BK KIT: Includes wedge lock & terminals.

MDR-4B 4-POSITION MALE RECEPTACLE OEM PART NUMBER: 74104-98BK KIT: Includes wedge lock & terminals.

MDP-6B 6-POSITION FEMALE PLUG

KIT: Includes wedge lock & terminals. OEM PART NUMBER: 74116-98BK

MDR-6B 6-POSITION MALE RECEPTACLE OEM PART NUMBER: 74106-98BK KIT: Includes wedge lock & terminals.

MDP-8B 8-POSITION FEMALE PLUG

KIT: Includes wedge lock & terminals. OEM PART NUMBER: 74118-98BK

MDR-8B

MDP-12B 12-POSITION FEMALE PLUG

8-POSITION MALE RECEPTACLE OEM PART NUMBER: 74108-98BK KIT: Includes wedge lock & terminals.

OEM PART NUMBER: 74119-98BK KIT: Includes wedge lock & terminals.

NAMZ CCP Inc. / DEUTSCH

18

CONNECTORS

DEUTSCH & JAE CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

MDR-12B

MDP-SOCKETS 100-PACK, FEMALE SOCKETS CRIMP TOOL: DSCT-02 OEM PART NUMBER: 74191-98

12-POSITION MALE RECEPTACLE KIT: Includes wedge lock & terminals. OEM PART NUMBER: 74109-98BK

MDR-PINS

DTM-HP 10-PACK, HOLE PLUGS

100-PACK, MALE SOCKETS OEM PART NUMBER: 72190-98 CRIMP TOOL: DSCT-02

USE: DTM Series only. OEM PART NUMBER: 74195-98

DTFPH-01 3-POSITION FUEL PUMP HEADER OEM PART NUMBER: 72435-00 KIT: Includes header only.

HDD-XL-KIT 1-POSITION MALE & FEMALE OEM PART NUMBER: (MALE) 72180-94 & (FEMALE) 72181-94. KIT: Includes terminals.

JAE The JAE MX-1900 Series were introduced in 2011 and first used on Softail models with the start of CAN/Bus technology. Being very small and watertight, these connectors attached handlebar switch wiring to the BCM, or Body Control Module. Available only in 2 and 4-position, male and female and stamped crimp terminals. Direct OEM replacement.

NJ-2S51 2-POSITION FEMALE SOCKET OEM PART NUMBER: 72906-11 Requires (2) FEMALE terminals.

NJ-2P51 2-POSITION MALE PIN HOUSING Requires (2) MALE terminals. OEM PART NUMBER: 72905-11

NJ-4S51 4-POSITION FEMALE SOCKET OEM PART NUMBER: 72908-11 Requires (4) FEMALE terminals.

NAMZ CCP Inc. / DEUTSCH / JAE

19

NAMZ CCP Inc. / DELPHI

JAE / JST CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

CONNECTORS

NJ-4S52 4-POSITION FEMALE SOCKET OEM PART NUMBER: 69201179 Requires (4) FEMALE terminals.

NJ-4P51 4-POSITION MALE PIN HOUSING Requires (4) MALE terminals. OEM PART NUMBER: 72907-11

NJ-4P52

NJ-19S

25-PACK, FEMALE PINS

4-POSITION MALE PIN HOUSING

CRIMP TOOL: NJC-990120 OEM PART NUMBER: 72910-11

OEM PART NUMBER: 69201180 Requires (4) MALE terminals.

NJ-19P

NJC-990120

NAMZ UNIVERSAL CRIMP TOOL

25-PACK, MALE PINS

Our “go-to” hand crimp tool in the shop when we need to crimp one or two quick open barrel / stamped terminals. Perfect for 30 to 18 gauge terminals.

OEM PART NUMBER: 72909-11 CRIMP TOOL: NJC-990120

JST Looking for space saving connectors? If space is at a premium, these are a perfect choice. They are found on Big Dog, Victory and HD Motorcycles. They are the smallest watertight connectors available and come in 2, 3, 4, 6 and 8-position. Terminals are stamped and sold in 100-packs and our NJC-990120 crimp tool is a must.

NJST-02R 2-POSITION RECEPTACLE OEM PART NUMBER: 69200305 KIT: Includes wire seal.

NJST-02P

NJST-03R

2-POSITION TAB KIT: Includes wire seal. Requires (2) MALE terminals.

3-POSITION RECEPTACLE

Requires (3) FEMALE terminals. KIT: Includes wire seal.

NAMZ CCP Inc. / JAE / JST

20

CONNECTORS

TERMINALS - WIRE SEALS - BUILDERS KITS JST CONNECTORS

NJST-04R

NJST-03P

3-POSITION TAB

4-POSITION RECEPTACLE Requires (4) FEMALE terminals. OEM PART NUMBER: 69200306

Requires (3) MALE terminals. KIT: Includes wire seal.

NJST-04P

NJST-06R

6-POSITION RECEPTACLE Requires (6) FEMALE terminals. OEM PART NUMBER: 69201162

4-POSITION TAB KIT: Includes wire seal. Requires (4) MALE terminals.

NJST-06P 6-POSITION TAB

NJST-08R

8-POSITION RECEPTACLE

Requires (6) male terminals. OEM PART NUMBER: 69201163

Requires (8) FEMALE terminals. KIT: Includes wire seal.

NJST-08P 8-POSITION TAB

NJST-RTERM

100-PACK, FEMALE TERMINALS

Requires (8) MALE terminals. KIT: Includes wire seal.

CRIMP TOOL: NJC-990120 OEM PART NUMBER: 69200307

NJC-990120 NAMZ UNIVERSAL CRIMP TOOL Our “go to” hand crimp tool in the shop when we need to crimp one or two quick open barrel / stamped terminals. Perfect for 30 to 18 gauge terminals.

NJST-PTERM 100-PACK, MALE TERMINALS OEM PART NUMBER: 69201164 CRIMP TOOL: NJC-990120

NAMZ CCP Inc. / JST

21

NAMZ CCP Inc. / DELPHI

MOLEX CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

MOLEX MX-150 The “factory,” started using the Molex MX-150 Series connectors in 2007. Making the switch from Deutsch connectors made sense since they took up more space. Molex connectors are more compact, watertight and easy to service when needed. These connectors are available from 2 to 20-position and in (4) colors.

CONNECTORS

NM-33471-0302 3-POSITION FEMALE PLUG OEM PART NUMBER: 72514-07GY Requires (3) female terminals.

NM-33472-4002 4-POSITION FEMALE PLUG OEM PART NUMBER: 72444-07GY Requires (4) female terminals.

NM-33481-0302 3-POSITION MALE RECEPTACLE Requires (3) male terminals. OEM PART NUMBER: 72513-07GY

NM-33482-4002 4-POSITION MALE RECEPTACLE Requires (4) male terminals. OEM PART NUMBER: 72415-07GY

NM-33472-0802 8-POSITION FEMALE PLUG OEM PART NUMBER: 72469-07GY Requires (8) female terminals.

NM-33482-0802 8-POSITION MALE RECEPTACLE Requires (8) male terminals. OEM PART NUMBER: 72447-07GY

NM-33472-1202 12-POSITION FEMALE PLUG Requires (12) female terminals. OEM PART NUMBER: 72489-07GY

NM-33482-1202

NM-33472-1602

12-POSITION MALE RECEPTACLE OEM PART NUMBER: 72490-07GY Requires (8) male terminals.

16-POSITION FEMALE PLUG OEM PART NUMBER: 72491-07GY Requires (16) female terminals.

NAMZ CCP Inc. / MOLEX

22

CONNECTORS

MOLEX CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

NM-33471-0201

NM-33482-1602

16-POSITION MALE RECEPTACLE

2-POSITION FEMALE PLUG OEM PART NUMBER: 69200271 Requires (2) female terminals.

Requires (16) male terminals. OEM PART NUMBER: 72492-07GY

NM-33481-0201

NM-33471-0301

3-POSITION FEMALE PLUG

2-POSITION MALE RECEPTACLE OEM PART NUMBER: 69200272 Requires (2) male terminals.

Requires (3) female terminals. OEM PART NUMBER: 72512-07BK

NM-33481-0301 3-POSITION MALE RECEPTACLE OEM PART NUMBER: 72511-07BK Requires (3) male terminals.

NM-33472-4001

4-POSITION FEMALE PLUG

Requires (4) female terminals. OEM PART NUMBER: 72177-07BK

NM-33482-4001 4-POSITION MALE RECEPTACLE Requires (4) male terminals. OEM PART NUMBER: 72175-07BK

NM-33472-0601

6-POSITION FEMALE PLUG

Requires (6) female terminals. OEM PART NUMBER: 72414-07BK

NM-33471-0601

NM-33482-3601

6-POSITION FEMALE PLUG

6-POSITION MALE RECEPTACLE

Requires (6) male terminals. OEM PART NUMBER: 72188-07BK

OEM PART NUMBER: 72483-08BK Fits: Throttle Control Actuator Requires (6) female terminals.

NAMZ CCP Inc. / MOLEX

23

NAMZ CCP Inc. / DELPHI

MOLEX CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

CONNECTORS

3-POS GREEN

NM-33472-0801 8-POSITION FEMALE PLUG OEM PART NUMBER: 72479-07BK Requires (8) female terminals.

SOLD EACH

FEMALE & MALE CONNECTORS

3-Position Male: OEM # 72534-07GN Requires (3) male terminals. 3-Position Female: OEM # 72540-07GN Requires (3) female terminals.

NM-33482-0801

NM-33472-1201

8-POSITION MALE RECEPTACLE

12-POSITION FEMALE PLUG

Requires (8) male terminals. OEM PART NUMBER: 72478-07BK

Requires (12) female terminals. OEM PART NUMBER: 72487-07BK

NM-33482-1201

NM-33472-1601

16-POSITION FEMALE PLUG OEM PART NUMBER: 72166-07BK Requires (16) female terminals.

12-POSITION MALE RECEPTACLE OEM PART NUMBER: 72488-07BK Requires (12) male terminals.

NM-33482-1601

NM-33472-2001

16-POSITION MALE RECEPTACLE OEM PART NUMBER: 72167-07BK Requires (16) male terminals.

20-POSITION FEMALE PLUG

Requires (20) female terminals. OEM PART NUMBER: 72500-07BK

NM-33471-0303

NM-33481-0303

3-POSITION FEMALE PLUG

3-POSITION MALE RECEPTACLE

Requires (3) female terminals. OEM PART NUMBER: 72542-07BN

Requires (3) male terminals. OEM PART NUMBER: 72541-07BN

NAMZ CCP Inc. / MOLEX

24

CONNECTORS

MOLEX & METRIC CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

100-PK

MOLEX TERMS

NM-31403-2100

2-POSITION FEMALE PLUG OEM PART NUMBER: 72720-07 USE: TSSM Security Antenna. KIT: Includes (2) terminals.

FEMALE & MALE TERMINALS NM-33012-1002: Female terminals. OEM PART NUMBER: 72169-07 OEM PART NUMBER: 72168-07 NM-33000-1002: Male terminals. NMX-CBK MOLEX MX-150 BUILDERS KIT Kit includes (2) 3 & 4, (4) 6 & 8, (3) 12 & 16-position connectors with (100) male & female terminals.

NM-34345-0001

10-PACK, HOLE PLUGS OEM PART NUMBER: 72473-07 USE: Molex MX-150 Series only.

METRIC SHUR & ML

NH-606002 50-PACK, FEMALE SHUR COVER USE: Cover for part # NH-606252. KIT: Includes 50 covers.

Our Metric line of connectors, terminals and seals are one of the most in-depth in the industry. You will find all of the most popularly used connectors on all of the major metric motorcycle manufacturers like Ducati, Triumph, Honda, Kawasaki, Suzuki and Yamaha. Very inexpensive, sold in bulk packs and a must for any custom shop or dealership.

NH-606252 50-PACK, FEMALE SHUR PLUG KIT: Includes 50 terminals. USE: Mates with part # NH-606302.

NH-606102

50-PACK, MALE SHUR COVER KIT: Includes 50 covers. USE: Cover for part # NH-606302.

NH-606302

NH-607301

50-PACK, MALE SHUR PLUG

50-PACK, DUAL FEMALE COVER

USE: Mates with part # NH-606252. KIT: Includes 50 terminals.

USE: Cover for part # NH-607202. KIT: Includes 50 covers.

NAMZ CCP Inc. / MOLEX / METRIC

25

NAMZ CCP Inc. / DELPHI

TERMINALS - WIRE SEALS - BUILDERS KITS METRIC CONNECTORS

CONNECTORS

NH-607202

NH-ML-3B

50-PACK, DUAL FEMALE PLUG KIT: Includes 50 terminals. USE: Mates with part # NH-607301.

3-POSITION FEMALE USE: Mates with part # NH-ML-3A. KIT: 5-Pack of connectors.

NH-ML-3A

NH-ML-4B

4-POSITION FEMALE USE: Mates with part # NH-ML-4A. KIT: 5-Pack of connectors.

3-POSITION MALE USE: Mates with part # NH-ML-3B. KIT: 5-Pack of connectors.

NH-ML-4A

NH-ML-6B

4-POSITION MALE USE: Mates with part # NH-ML-4B. KIT: 5-Pack of connectors.

6-POSITION FEMALE USE: Mates with part # NH-ML-6A. KIT: 5-Pack of connectors.

NH-ML-6A

NH-ML-2BL

6-POSITION MALE

2-POSITION LOCKING FEMALE

KIT: 5-Pack of connectors. USE: Mates with part # NH-ML-6B.

KIT: 5-Pack of connectors. USE: Mates with part # NH-ML-2AL.

NH-ML-2AL

NH-ML-3BL

2-POSITION LOCKING MALE

3-POSITION LOCKING FEMALE USE: Mates with part # NH-ML-3AL. KIT: 5-Pack of connectors.

KIT: 5-Pack of connectors. USE: Mates with part # NH-ML-2BL.

NAMZ CCP Inc. / METRIC

26

CONNECTORS

METRIC CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

NH-ML-4BL

NH-ML-3AL

3-POSITION LOCKING MALE USE: Mates with part # NH-ML-3BL. KIT: 5-Pack of connectors.

4-POSITION LOCKING FEMALE USE: Mates with part # NH-ML-4AL. KIT: 5-Pack of connectors.

NH-ML-4AL

NH-ML-6BL

6-POSITION LOCKING FEMALE USE: Mates with part # NH-ML-6AL. KIT: 5-Pack of connectors.

4-POSITION LOCKING MALE USE: Mates with part # NH-ML-4BL. KIT: 5-Pack of connectors.

NH-ML-6AL 6-POSITION LOCKING MALE KIT: 5-Pack of connectors. USE: Mates with part # NH-ML-6BL.

NH-ML-9BL

9-POSITION LOCKING FEMALE USE: Mates with part # NH-ML-9AL. KIT: 5-Pack of connectors.

NH-ML-9AL 9-POSITION LOCKING MALE KIT: 5-Pack of connectors. USE: Mates with part # NH-ML-9BL.

NH-604101

100-PK, FEMALE ML TERMINALS

USE: ML Series only. KIT: Includes 100 terminals.

NH-605123

NDC-990170 NAMZ UNIVERSAL CRIMP TOOL Our “go-to” hand crimp tool in the shop when we need to crimp one or two quick open barrel / stamped terminals. Perfect for 22 to 14 gauge terminals.

100-PK, MALE ML TERMINALS

USE: ML Series only. KIT: Includes 100 terminals.

NAMZ CCP Inc. / METRIC

27

NAMZ CCP Inc. / DELPHI

METRIC CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

METRIC 250 SERIES

CONNECTORS

NH-RB-1B

The 250-Series is another very popular connector series. Its name derives from the size of the female and male terminals, .25”. These connectors are offered with or without a positive lock. Available from 2 through 6-position, with / without mounting tabs and male and female stamped brass terminals. Found on most metric bikes, these are a perfect replacement.

1-POSITION FEMALE USE: Mates with part # NH-RB-1A. KIT: 5-Pack of connectors.

NH-RB-1A

NH-RB-2B

2-POSITION FEMALE USE: Mates with part # NH-RB-2A. KIT: 5-Pack of connectors.

1-POSITION MALE USE: Mates with part # NH-RB-1B. KIT: 5-Pack of connectors.

NH-RB-2A

NH-RB-3B

2-POSITION MALE

3-POSITION FEMALE USE: Mates with part # NH-RB-3A. KIT: 5-Pack of connectors.

KIT: 5-Pack of connectors. USE: Mates with part # NH-RB-2B.

NH-RB-3A

NH-RB-4B

3-POSITION MALE

4-POSITION FEMALE USE: Mates with part # NH-RB-4A. KIT: 5-Pack of connectors.

KIT: 5-Pack of connectors. USE: Mates with part # NH-RB-3B.

NH-RB-4A

NH-RB-6BT

4-POSITION MALE

6-POSITION FEMALE, MOUNT TAB

KIT: 5-Pack of connectors. USE: Mates with part # NH-RB-4B.

KIT: 5-Pack of connectors. USE: Mates with part # NH-RB-6AF.

NAMZ CCP Inc. / METRIC

28

CONNECTORS

TERMINALS - WIRE SEALS - BUILDERS KITS METRIC CONNECTORS

NH-RB-2BSL

NH-RB-6AF

6-POSITION MALE, MOUNT TAB USE: Mates with part # NH-RB-6BT. KIT: 5-Pack of connectors.

2-POSITION LOCKING FEMALE USE: Mates with part # NH-ML-2ASL. KIT: 5-Pack of connectors.

NH-RB-2ASL

NH-RB-3BSL

3-POSITION LOCKING FEMALE USE: Mates with part # NH-ML-3ASL. KIT: 5-Pack of connectors.

2-POSITION LOCKING MALE

KIT: 5-Pack of connectors. USE: Mates with part # NH-RB-2BSL.

NH-RB-3ASL 3-POSITION LOCKING MALE USE: Mates with part # NH-ML-3BSL. KIT: 5-Pack of connectors.

NH-RB-4BSL

4-POSITION LOCKING FEMALE USE: Mates with part # NH-RB-4ASL. KIT: 5-Pack of connectors.

NH-RB-4ASL 4-POSITION LOCKING MALE KIT: 5-Pack of connectors. USE: Mates with part # NH-RB-4BSL.

NH-RB-6BSL

6-POSITION LOCKING FEMALE USE: Mates with part # NH-RB-6ASL. KIT: 5-Pack of connectors.

NH-RB-6ASL

NH-604512 50-PACK, FEMALE 250 TERMINALS KIT: Includes 50 terminals. USE: 250 Series only.

6-POSITION LOCKING MALE

KIT: 5-Pack of connectors. USE: Mates with part # NH-RB-6BSL.

NAMZ CCP Inc. / METRIC

29

NAMZ CCP Inc. / DELPHI

METRIC CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

CONNECTORS

NH-605502 50-PACK, MALE 250 TERMINALS KIT: Includes 50 terminals. USE: 250 Series only.

NDC-990170 NAMZ UNIVERSAL CRIMP TOOL Our “go-to” hand crimp tool in the shop when we need to crimp one or two quick open barrel / stamped terminals. Perfect for 22 to 14 gauge terminals.

METRIC HM SERIES

NS-6180-2451

Our Sealed HM-Series is a perfect connector for use in off-road or watercraft applications where a water- tight, positive locking connection is a must. Found on metric motorcycles, ATV’s and personal watercraft, available in 2, 3, 4 and 6-positions, male and female with stamped mating terminals. Wire seals and terminals are both sold separately in 50-piece packs.

2-POSITION FEMALE Requires (2) FEMALE terminals & seals.

KIT: (1) connector only.

NS-6187-2801

NS-6180-3451

2-POSITION MALE

3-POSITION FEMALE Requires (3) FEMALE terminals & seals.

Requires (2) MALE terminals & seals.

KIT: (1) connector only.

KIT: (1) connector only.

NS-6187-3801

NS-6180-4181

3-POSITION MALE Requires (3) MALE terminals & seals.

4-POSITION FEMALE

Requires (4) FEMALE terminals & seals.

KIT: (1) connector only.

KIT: (1) connector only.

NS-6187-4441

NS-6180-6181

6-POSITION FEMALE

4-POSITION MALE

Requires (4) MALE terminals & seals.

Requires (6) FEMALE terminals & seals.

KIT: (1) connector only.

KIT: (1) connector only.

NAMZ CCP Inc. / METRIC

30

CONNECTORS

METRIC CONNECTORS TERMINALS - WIRE SEALS - BUILDERS KITS

NS-1500-0106

NS-6187-6801

6-POSITION MALE

50-PACK, FEMALE HM TERMINALS

KIT: Includes 50 terminals.

Requires (6) MALE terminals & seals.

USE: HM & MT Series only.

KIT: (1) connector only.

NS-1500-0105

NS-7160-8234

50-PACK, HM WIRE SEALS

50-PACK, MALE HM TERMINALS

KIT: Includes 50 wire seals.

KIT: Includes 50 terminals.

USE: Crimp with male & female terminals .

USE: HM & MT Series only.

METRIC MT SERIES

NS-6180-2321

Our Sealed MT-Series is also a perfect connector for use in off-road or watercraft applications where a watertight, positive locking connection is a must. Found on metric motorcycles, ATV’s and personal watercraft, available in 2, 3, 4 and 6-positions, male, female with stamped terminals. Wire seals and terminals are both sold separately in 50-piece packs.

2-POSITION LOCKING FEMALE Requires (2) FEMALE terminals & seals.

KIT: (1) connector only.

NS-6187-2311 2-POSITION LOCKING MALE

NS-6180-3241

3-POSITION LOCKING FEMALE Requires (3) FEMALE terminals & seals.

Requires (2) MALE terminals & seals.

KIT: (1) connector only.

KIT: (1) connector only.

NS-6187-3231

NS-6180-4771 4-POSITION LOCKING FEMALE

3-POSITION LOCKING MALE Requires (3) MALE terminals & seals.

Requires (3) FEMALE terminals & seals.

KIT: (1) connector only.

KIT: (1) connector only.

NAMZ CCP Inc. / METRIC

31

NAMZ CCP Inc. / DELPHI