ProGARM Catalogue

EN 13034 PROTECTIVE CLOTHING AGAINST LIQUID CHEMICALS

EN 342 PROTECTION AGAINST COLD

EN 14404 KNEE PROTECTION

EN 343 PROTECTIVE AGAINST RAIN

This EN standard specifies the requirements and test methods for garments and clothing combinations designed to protect the wearer in a cold environment (characterised by a combination of humidity, wind and air temperature lower than -5 °C). The standard does not contain any specific requirements for head, hand or foot protection. ABOUT THIS EN STANDARD This standard’s pictogram is an ice-crystal placed alongside three figures that represent the insulation (Clo), air permeability (X) and, if applicable, the water vapour resistance (Y) values. The precise meaning of these values is explained below. THE CLO, X AND Y VALUES The Clo value indicates a garment’s insulation properties and is a measurement of how long a person can work at a specific temperature when wearing this clothing. It is not a specific class, but can be any value. The table below shows the significance of the Clo value.

Personal protective equipment. Knee protectors for work in the kneeling position.

ProGARM ® produces garments to protect wearers against liquid chemicals in accordance with this European Standard. These garments are suitable for use in environments where there may be a risk of chemical splashes but where a total chemical barrier is not required - *PB = Partial Body Protection. The EN 13034 standard specifies the requirements and test methods for Type 6 chemical protection suits for both one-off and multiple use applications. For other related accessories, such as gloves and boots, which are not an integral part of the suit, please refer to the corresponding product standards (see Product Matrix on page 102). Clothing in this category provides limited protection against small spatters or fumes of liquid chemicals. It is usually made of water- repellent, but not completely waterproof materials. Within the ProGARM ® range of products this is often achieved by the use of chemical coatings such as Teflon®, which repel the contaminants and in order to preserve these properties within the fabric of the garment, special washing and drying instructions should be adhered to. ABOUT THIS EN STANDARD The fabric is tested in various ways to determine its tensile strength and resistance to chemicals. In these tests, four different solutions of chemicals (Sulphuric Acid H2S04 30%, SodiumHydroxide NaHO 30%, 0-xylene undiluted and 1-butanol undiluted) are applied to a fabric sample and the quantities of liquid that drip off and penetrate the fabric are measured and analysed must be within the tolerances set within the standard. One finished product (of each quality) must also be analysed in a ‘mannequin’ test. During this spray test, the wearer must perform 7 movements (these are described in the standard) and the permeability of the garment to liquid chemicals is subsequently determined. The classes attained in the various tests must be clearly listed in the user instructions for the garment. Where certified to EN 13034 ProGARM ® garments are Type 6 garments and must undergo the spray test in order to display the EN pictogram for the standard on the user information and garment Care Label. In some of our garments it should be noted that in some instances the fabric has been tested but the garment and seams have not. In this case, this is clearly marked on the Care Label and the EN pictogram is not shown. Other requirements within the EN 13034 standard include tests for water resistance, tear strength, tensile strength and seam strength. If 2 piece garments are to be worn such as a trouser and jacket combination it is important to ensure that both garments have been certified as a ‘set’ for the specified level of protection. If chemicals are splashed onto a garment, the wearer should immediately move away from the affected area and carefully remove the garment, ensuring that the chemicals or liquids do not come into contact with any part of the skin. The garment must then be cleaned and assessed for future use or taken out of use.

This EN Standard specifies the requirements and test methods for materials and the seams of protective clothing that has been designed to give protection against precipitation (i.e. rain, snow), mist and ground moisture. There is also a separate test EN 14360 for assessing the waterproofness of the complete finished garments but this test is not included in EN 343. ABOUT THIS EN STANDARD This standard’s icon shows an umbrella placed under two numbers that represent the X and Y values. The X value indicates the waterproofness and the Y value indicates the water vapour permeability (the garment’s breathability). This standard falls within the scope of ‘self-certification’. This means that manufacturers are allowed to certify their own products, which therefore do not need to be assessed by an life-threatening hazard. If EN 343 is used in combination with other EN Standards the whole combination of standards is assessed by the notified body THE X AND Y VALUES The X value indicates the waterproofness of the garment. There are 4 classes with 4 being the highest (i.e. the most waterproof) and 1 is the lowest. A specific quantity of pressurised water is applied to the fabric and the respective Class is derived from the amount of pressure the fabric can withstand. The Y value indicates the breathability of the fabric/s (all the layers used in the article). There are also 4 classes for breathability with Class 1 being the lowest and Class 4 the highest. Wearing Class 1 garments longer than x minutes is not recommended (the length of time the article may be worn (x) is given in the standard in a table). independent notified body. This is because the only risk to the wearer is that he/she might get wet, which is not a

ProGARM ® produces safety garments that are certified in accordance with the EN 14404 Type 2 standard. This EN Standard relates to trousers and coveralls which offer kneepad pockets to protect the wearer when kneeling. ABOUT THIS EN STANDARD EN 14404 only applies in combination with certified kneepads and a garment that has been assessed. All ProGARM ® workwear garments with knee pockets comply with EN 14404 and have been assessed accordingly by a notified body. The measurements prescribed for kneepads depend on the size of the garment in which they are used. The ProGARM ® Gel Foam kneepads is our recommended kneepad for use in our garments to ensure the pad fits the pocket and offers protection for wearers from short to long leg lengths. There are three properties of knee protectors that are tested - these are Penetration Resistance, Force Distribution and Shock Absorption. Two levels of protection can be provided. The ProGARM ® Gel Foam Kneepad has been tested according to and meets the requirements for EN14404 Level 1. Level 1: This level requires kneepads to provide protection on a surface on which the wearer will not generally risk injury from lying objects more than 1cm high. Penetration resistance of at least 100 N. Level 2: This level requires kneepads to be able to withstand use under heavy conditions, such as kneeling on stones in mines and quarries. Penetration resistance of at least 250 N.

LIGHTACTIVITY115W/M 2

AVERAGEACTIVITY170W/M 2

CLO

8H/ ˚ C

1H/ ˚ C

8H/ ˚ C

1H/ ˚ C

2.0

1

-23

-18

-31

2.5

-6

-33

-29

-44

3.0

-13

-43

-39

-57

The X value indicates a garment’s air permeability. The X value has 3 classes (1 to 3). Class 1 garments have the highest air permeability and Class 3 the least. The air permeability is a wind proofing measurement, Class 1 is therefore the least windproof and Class 3 the most. The Y value indicates a garment’s water vapour resistance. The Y value also has 3 classes (1 to 3). Class 1 garments have the lowest water vapour resistance and Class 3 garments the highest. The new version has the following values: Icler / Icle, this is the equivalent of the Clo value and two Y values. The first Y value indicates the air permeability; it is assessed in a different way to the old EN 342, but is still given as Class 1 to 3. The second Y value indicates the garment’s waterproofing. Clothing that complies with EN 342 does not necessarily have to be waterproof. This value can therefore sometimes be omitted. This value has 2 classes - 1 and 2. Class 1 is the least waterproof and Class 2 the most. If a garment is waterproof, its breathability must also be tested. A more recent version (2004) of EN 342 is now available.

100

101

WWW.PROGARM.COM

+44 (0)1482 679600 - INFO@PROGARM.COM