Catalog FORMAT plus - EDE 2015 - 2017

325

Milling Cutters

m

Solid Carbide Vari-Helix 4 Flute Endmill

Design: Ultra-fine grit solid carbide, type NH, DIN 6527 L, 40°/42°, fire-coated, with centre cut. Application: Can be used for peripheral milling as well as for universal machining. For milling depths up to 2 x D. Can also be used for trim- ming and finishing milling. Can be used for rough grinding, slot cutting and finishing milling. The irregular spiral lead 40°/42° results in parti- cularly smooth running and thus very good surface on the workpiece. A much longer tool life is achieved than with conventional tools.

VHM UF Solid carbide F

Typ NH

y e

Z 4

DIN 6527

DIN 6535-HA

DIN 6535-HA

40°/42°

9°

l 1

d 1

d 2

l 2

2 Cutting Tools

2513 Fire

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

2513

200

160

60

180

350

130

100

70

200

6WHHOV XSWR

2513

dia.

Order No.

Cutting edge length l 2 mm

Overall length l 1 mm

Neck ∅ d 3 mm

Shaft dia. d 2 = h6 mm

1PP

d 1

= h10 mm

f z mm

Fire

0400 0500 0600 0800 1000 1200 1600 2000

4 5 6 8

26.30 26.30 32.00 44.20 67.10 85.40

11 13 13 19 22 26 32 38

57 57 57 63 72 83 92 104

3.7 4.7 5.5 7.5 9.2 11.2 15.0

6 6 6 8

0.028 0.028 0.039 0.053 0.065 0.079 0.095 0.110

10 12 16 20

10 12 16 20

148.00 230.00

19.00

(221)

Solid Carbide Vari-Helix 4 Flute End Mill with Through Coolant

Design: Ultra-fine grit solid carbide, type NH, DIN 6527 L, 40°/42°, fire-coated, with centre cut. Cutting speed approx. 50% higher than with non-coated tools. Dry machining possible. With inner cooling: Increase in tool life of up to 50%, since chip blockage is reduced. Application: Can be used for peripheral milling as well as for universal machining. For milling depths up to 2 x D. Can also be used for trimming and finishing milling. Can be used for rough grinding, slot cutting and finishing milling. The irregular spiral lead 40°/42° results in particularly smooth running and thus very good surface on the workpiece. A much longer tool life is achieved than with conventional tools.

VHM UF Solid carbide UF

Z 4

DIN 6527

Typ NH

y e

DIN 6535-HB

40°/42°

9°

Fire

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

2454

170

170

70

70

200

140

130

6WHHOV XSWR

2454

dia.

Order No.

Cutting edge length l 2 mm

Overall length l 1 mm

Neck ∅ d 3 mm

Shaft dia. d 2 = h6 mm

1PP

d 1

= h10 mm

f z mm

Fire

0600 0800 1000 1200 1600 2000

6 8

61.90 81.90

13 19 22 26 32 38

57 63 72 83 92

5.5 7.5 9.2

6 8

0.036 0.052 0.066 0.085 0.100 0.120

10 12 16 20

121.00 156.00 268.50 411.00

10 12 16 20

11.2 15.0 19.0

104

(221)

2/79

Articles marked ◊ are not held in stock, procurement is effected at short notice.

Not all items are available in every country.