Kaman Product Catalog 1050

120 / 436

Single Reduction
Worm Gear Reducers
Double Reduction
Worm - Worm Gear Reducers
Double Reduction
Helical - Worm Gear Reducers
WASHGUARD
® Reducers
and GEAR+MOTOR™
Ratio Multipliers
Accessories and
Additional Capabilities
120
Note: This chart is meant as a guide for reducer selections at specific motor horsepowers.
Actual service factor may be greater than indicated. For actual service factors and maximum worm reducer ratings, refer to pages 122-126.
♠ Actual ratio combinations supplied by Factory may vary from above depending on application and manufacturing requirements.
Refer to page 131 for exact ratio of double reduction worm-worm gear reducers.
* Size 832 must be used for NH Series for this selection.
** Size 842 must be used for NH Series for this selection.
indicates a selection where a smaller reducer (1 case size) can be used with redesigned product due to rating increase.
indicates a selection where a smaller reducer (2 case sizes) can be used with redesigned product due to rating increase.
1.00 Service Factor
Nominal Output Input Horsepower @ 1750 RPM
Ratio♠ RPM 1/8 1/6 1/4 1/3 1/2 3/4 1 1-1/2 2 3 5 7-1/2 10 15 20 25
75 23.3 813 813 815 815 821 824 826 830 832** 842 852 860 880 880 8100 8100
100 17.5 813 813 815 815 821 824 826 830* 842 842 852 860 880 8100 8100
150 11.7 813 815 821 821 824 826 830* 832** 842 852 852 880 8100 8100
200 8.75 815 815 821 824 826 830 832 842 842 852 870 880 8100
250 7.00 815 818 821 824 826 830* 832** 842 852 852 880 8100 8100
300 5.83 815 821 824 824 830 832 842 842 852 852 880 8100 8100
400 4.38 821 821 824 826 830* 842 842 852 852 860 8100 8100
500 3.50 821 824 826 830 832 842 842 852 852 880 8100
600 2.92 821 824 826 830 832 842 852 852 860 880 8100
750 2.33 824 824 830 830* 842 842 852 852 870 8100 8100
900 1.94 824 826 830 832 842 842 852 852 880 8100
1000 1.75 824 830 830 832 842 842 852 860 880 8100
1200 1.46 824 830 830* 832 842 852 852 870 880 8100
1500 1.17 830 830 832 842 842 852 860 880 8100 8100
1800 9.72 830 830 832 842 852 852 860 8100 8100
2400 .729 830 830* 842 842 852 852 880 8100 8100
3000 .583 830 830* 842 842 852 852 880 8100
3600 .486 830* 832** 842 852 852 880 8100
Nominal Output Input Horsepower @ 1750 RPM
Ratio♠ RPM 1/8 1/6 1/4 1/3 1/2 3/4 1 1-1/2 2 3 5 7-1/2 10 15 20 25
75 23.3 813 813 815 818 821 824 830 832** 842 842 852 880 880 8100 8100
100 17.5 813 815 815 821 824 826 830 832** 842 842 852 880 880 8100
150 11.7 815 815 821 824 826 830 832 842 842 852 870 880 8100
200 8.75 815 821 824 824 830 832 842 842 852 852 880 8100 8100
250 7.00 815 821 824 826 830 832** 842 842 852 852 880 8100
300 5.83 818 821 824 826 830* 842 842 852 852 870 8100 8100
400 4.38 821 824 826 830 832 842 842 852 852 880 8100
500 3.50 824 824 830 830* 842 842 852 852 860 880 8100
600 2.92 824 824 830 832 842 842 852 852 870 8100
750 2.33 824 826 830 832 842 852 852 860 880 8100
900 1.94 824 830 830* 832** 842 852 852 880 880 8100
1000 1.75 826 830 830* 842 842 852 852 880 8100 8100
1200 1.46 830 830 832 842 842 852 852 880 8100 8100
1500 1.17 830 830 842 842 852 852 880 8100 8100
1800 9.72 830 832 842 842 852 860 880 8100 8100
2400 .729 830 842 842 852 852 880 8100 8100
3000 .583 830* 842 842 852 852 880 8100
3600 .486 832** 842 842 852 852 8100 8100
How to Use
Based on required output RPM and input motor horsepower, read across chart for the
appropriate reducer size. As a rule of thumb, use 1.00 service factor chart for applications
having uniform loads with up to 10 hours service duration per day. Use 1.25 service factor
chart for longer service or shock loading. These charts are to be considered as guides
only. Typically double reduction reducers are selected based on application torque, not
necessarily HP. Refer to page 418 or contact Factory with specific application information.
Reducer size corresponds to center distances of secondary stage reducer, as shown in the
chart below.
Quick Selections