41 / 114
PAGE 41
PRICES SUBJECT TO CHANGEWITHOUT NOTICE
GTC BEARING SYSTEM PIVOT PINS
GTC
440C stainless steel thrust ball bearings
caged in stainless steel retainers developed
by
Gustavo T. Cecchini's GTC Knives
to
reduce friction and failures, increase opening
time, and easier cleaning. The 100% stainless
steel construction eliminates the problems
of other thrust bearings that are not 100%
stainless. Install by cutting a pocket, with
a counterbore, in both the blade and frame.
Use one bearing in blade and one in the
frame. Some prefer to cut the pocket in both
frames, and not in the blade. This is a good
solution when the blade is already hardened.
Sold Each.
The Path Maker is used to provide a smooth
raceway for the thrust bearing balls to slide
along. The Path Maker is used in a drill
press to mark the raceway into the blade and
liners. This task is performed by setting your
drill press at 500 RPM and applying a light
down pressure for a few seconds. Check the
surface for marking until a circular raceway
is visible, then this task is complete. We
recommend that you complete this task to the
blade before and after heat treat to guarantee
the elimination of all tooling marks. You will
need a different Path Maker for each bearing
size and each pivot size that you use. The
final assembly should use new bearings only.
A bearing will be included with each Path
Maker.
The illustration (above left) shows the pocket
in the left liner once the procedure has been
completed. The first bearing will fit in this
pocket. The second pocket should be cut in
the blade. In final assembly (see above right),
the liner pocket and blade pocket should
be facing up when the knife is in the proper
position for assembly.
There should be a
raceway path on each
side of a thrust bearing.
The illustration above
shows the right liner
with
the
raceway
path completed. This
raceway matches up
to the blade pocket
thrust bearing. This procedure should be
completed on both sides of the blade. This
will match up with the raceway needed in the
liner pocket thrust bearing. When finished
you will have made a raceway path on all four
bearing surfaces and you should be ready for
assembly.
Select the counterbore to fit the bearing and
pivot pin combination listed below, also listed
are the proper depths to cut the pocket.
Reamers are .0005" oversize. Ream blade
and liners for pivot pins.
SIZE 1 - SMALL BEARING
SIZE 1 - SMALL BEARING (GC101, GC106)
SIZE 2 - MEDIUM BEARING
SIZE 2 - MEDIUM BEARING (GC111)
SIZE 3 - LARGE BEARING
SIZE 3 - LARGE BEARING (GC121)
SIZE 4 - HEAVY DUTY BEARING
SIZE 4 - HEAVY DUTY BEARING (GC102)
CAT.# O.D.
I.D.
BALL SIZE PRICE
GC101
.354" .157" .062" Small - 1
1.29
GC106
.358" .192" .062" Small - 1
1.29
GC111
.378" .218" .062" Med. - 2
1.29
GC121
.415" .255" .062" Large - 3
1.29
GC102
.454" .258" .078" Heavy - 4
1.29
CAT.# O.D. LENGTH HEAD TORX PRICE
F80
5/32" .350" 7/32" T6
6.95
F82
5/32" .500" 7/32" T6
6.95
F85
3/16" .350" 1/4" T7
6.95
F88
3/16" .500" 1/4" T7
6.95
F96
1/4" .350" 5/16" T8
6
.95
F98
1/4" .500" 5/16" T8
6.95
CAT.# SIZE PIVOT BEARING PRICE
RA755
23/64" 5/32" GC101
19.95
RA757
23/64" 3/16" GC106
19.95
CAT.# SIZE PIVOT DEPTH PRICE
RA855
23/64" 5/32" .050"
49.95
RA857
23/64" 3/16" .050"
49.95
CAT.# SIZE PIVOT BEARING PRICE
RA774
27/64" 1/4" GC121
19.95
CAT.# SIZE PIVOT DEPTH PRICE
RA874
27/64" 1/4" .050"
59.95
CAT.# SIZE PIVOT BEARING PRICE
RA763
25/64" 3/16" GC111
19.95
RA765
25/64" 5/32" GC111
19.95
CAT.# SIZE PIVOT DEPTH PRICE
RA863
25/64" 3/16" .050"
49.95
RA865
25/64" 5/32" .050"
49.95
CAT.# SIZE PIVOT BEARING PRICE
RA784
15/32" 1/4" GC102
19.95
CAT.# SIZE PIVOT DEPTH PRICE
RA884
15/32" 1/4" .066"
59.95
CAT.# SIZE PIVOT SIZE PIVOT PIN PRICE
RA1570
.1570" 5/32" F80 & F82
11.95
RA1880
.1880" 3/16" F85 & F88
12.95
RA2505
.2505" 1/4" F96 & F98
14.95
Precision ground and hardened 416 Stainless
steel (tolerance +/- .0002) for smooth action
on folders. Will work with the
GTC Bearings
and on folders without ball bearings. 5/32"
threaded 4-48, 3/16" and 1/4" threaded 6-48.
Pivot pin includes 2 plain Torx head screws.
CAT.# O.D. LENGTH FITS PRICE
F85B
3/16"
.350"
1/4"
1.95
F88B
3/16"
.500"
1/4"
1.95
F96B
1/4"
.350"
5/16"
1.95
F98B
1/4"
.500"
5/16"
1.95
Pivot barrels are threaded 6-48.
Bullseye Cosmos Texas Star
Orion
Six Shooter Jupiter Windmill Constellation
Solar Flare Flower
Gear
Sunburst
Spinner Galaxy Orchid Turbine
CAT. #
NAME QUANTITY PRICE
FF271
Solar Flare Stainless
2.49
FF272
Flower
Stainless
2.49
FF273
Gear
Stainless
2.49
FF274
Sunburst
Stainless
2.49
FF275
Bulls Eye Stainless
2.49
FF276
Cosmos Stainless
2.49
FF277
Texas Star
Stainless
2.49
FF278
Orion
Stainless
2.49
FF279
Six Shooter Stainless
2.49
FF280
Jupiter
Stainless
2.49
FF281
Windmill
Stainless
2.49
FF282
Constellation Stainless
2.49
CAT. #
NAME MATERIAL PRICE
FF401
Spinner
Stainless
2.49
FF402
Galaxy
Stainless
2.49
FF403
Orchid Stainless
2.49
FF404
Turbine Stainless
2.49
5/16" torx head diameter threaded 6-48.
Length .350". Use T8 torx wrench.
1/4" torx head diameter threaded 6-48.
Length .350". Use T6 torx wrench.
Add a custom touch to your folding knife with
our beautifully embellished Torx head screws.
Designed and manufactured by Jantz in Davis
Oklahoma from 303 stainless steel. For use
with our threaded pivot barrels.
5/16
" Diameter Torx Head
1/4
" Diameter Torx Head
Decorative Torx Screws
for Pivot Pins
Bearing System
Path Maker
Counterbores
Made in the USA.
Reamers
Path Makers
Pivot Pins
Threaded Pivot Only