159 / 1618
1/141
Articles marked ◊ are not held in stock, procurement is effected at short notice.
Cutting Tools
1
Design:
HSS, DIN 9-B with left spiral approx. 7°. The uneven tooth pitch ensure chatter-free
and accurate drilling. With cylinder shank with square drive. Bright surface
Application:
For reaming conical holes for taper pins according to DIN 1, DIN 258, DIN 1447,
DIN 7977 and DIN 7978. Perfectly suited for single production or repair work. Also suitable for
holes with interrupted cut. Pre-drill with a cylindrical spiral drill or pin drill.
Particularly suitable for steels up to 500 N/mm
2
in strength such as non-ferrous metals,
plastics, steels up to 1000 N/mm
2
amd casting materials.
Note:
Tap wrenches for manual actuation – see
Ç
1/223.
Order
No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al, Al and
Mg alloys
Copper,
brass,
bronze
1508
C
C
V
V
V
U
U
U
Order
No.
Nominal ∅
mm
1508
bright
Small/large ∅
mm
Cutting length
mm
Total length
mm
Width of keys
mm
0300
3
19.30
2.90/ 4.06
58
80
3.0
0400
4
21.90
3.90/ 5.26
68
93
3.8
0500
5
23.00
4.90/ 6.36
73
100
4.9
0600
6
27.90
5.90/ 8.00
105
135
6.2
0800
8
43.20
7.90/10.80
145
180
8.0
1000
10
61.00
9.90/13.40
175
215
10.0
1200
12
77.60
11.80/16.00
210
255
11.0
1300
13
90.30
12.80/17.00
210
255
12.0
1400
14
95.40
13.80/18.00
210
255
12.0
1600
16
107.50
15.80/20.40
230
280
14.5
2000
20
140.00
19.80/24.80
250
310
18.0
(W140)
Hand cone reamer
bright
Design:
HSS, DIN 2179 with left spiral approx. 45°. The uneven tooth pitch ensure chatter-free
and accurate drilling. With cylinder shank Bright surface
Application:
For reaming conical holes for taper pins according to DIN 1, DIN 258, DIN 1447,
DIN 7977 and DIN 7978. Perfectly suited for single and serial production. Optimum angle
accuracy for the reamed hole when using a floating reamer chuck. Pre-drill with a pin drill
(order no. 1052).
Particularly suitable for steels up to 500 N/mm
2
in strength such as non-ferrous metals,
plastics, steels up to 1000 N/mm
2
amd casting materials.
Order
No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al, Al and
Mg alloys
Copper,
brass,
bronze
1510
C
C
V
V
V
U
U
U
Order
No.
Nominal ∅
mm
1510
bright
Small/large ∅
mm
Cutting length
mm
Total length
mm
Shank ∅ h9
mm
0200
2.0
24.80
1.90/ 2.86
48
86
3.15
0250
2.5
29.60
2.40/ 3.36
48
86
3.15
0300
3.0
27.00
2.90/ 4.06
58
100
4.00
0400
4.0
27.30
3.90/ 5.26
68
112
5.00
0500
5.0
29.00
4.90/ 6.36
73
122
6.30
0600
6.0
33.20
5.90/ 8.00
105
160
8.00
0800
8.0
49.50
7.90/10.80
145
207
10.00
1000
10.0
63.40
9.90/13.40
175
245
12.50
1200
12.0
79.20
11.80/16.00
210
290
16.00
(W140)
Machine cone reamer
bright
HSS-E
DIN
2179
approx. 45°
1:50
HSS
DIN
9-B
approx. 7°
1:50
Reamers
159