773 / 1618
4/53
Articles marked ◊ are not held in stock, procurement is effected at short notice.
Measuring
Equipment
4
Design:
Clamping shaft and measuring bolts made of rustproof, hardened steel. Digit height on
LCD display 8.5 mm, operating and display part can be rotated by 280°. With interchangeable
stylus tips M2.5. Clamping shaft ∅ 8 mm, protective cap at end of measuring bolt. With data
output via radio transmission, RS 232, USB and Digimatic. Supplied with battery CR 2450, 3 V.
Functions:
Automatic on and off switch, mm/inch switching, automatic activation by moving
switch, key lock set for zero position, re-zeroing after switching deleted (absolute system),
MAX/MIN storage for reversal point search,
tolerance entry, ABS (switching from relative
to absolute measurement), reset (zeroing) possible at each position, counting direction change,
± pre-set function (setting a numerical value).
Note:
Suitable measuring inserts M2.5 are found on
Ç
4/49. .
Lifting cap (Order No. 4246 0165,
Ç
4/54).
Eyelet rear wall (Order No. 4246 0175,
Ç
4/54).
Radio receiver (Order No. 4942 0030,
Ç
4/129).
Transmitter module for e-Stick (Order No. 4942 0040,
Ç
4/130).
Data cable RS 232 (Order No. 4942 0055,
Ç
4/130).
Data cable USB (Order No. 4942 0050,
Ç
4/130).
Data cable Digimatic (Order No. 4246 0185,
Ç
4/54).
Order
No.
Measurement range
mm
4246
Reading
mm
Housing ∅
mm
Accuracy
mm
With radio
transmission
0110
12.5
431.00
0.0005 60.5
0.004
–
0120
12.5
463.00
0.0005 60.5
0.004
•
0115
25.0
489.00
0.0005 60.5
0.004
–
0125
25.0
522.00
0.0005 60.5
0.004
•
(W488)
Digital dial gauge for concentricity and evenness testing
Design:
Clamping shaft and measuring bolts made of rustproof, hardened steel. Digit height on
LCD display 8.5 mm, operating and display part can be rotated by 280°. With interchangeable
stylus tips M2.5. Clamping shaft ∅ 8 mm, protective cap at end of measuring bolt. With data
output via radio transmission, RS 232, USB and Digimatic. Supplied with battery CR 2450, 3 V.
Functions:
Automatic on and off switch, mm/inch switching, automatic activation by moving
switch, key lock set for zero position, re-zeroing after switching deleted (absolute system), MAX/
MIN storage for reversal point search, tolerance entry, ABS (switching from relative to absolute
measurement), reset (zeroing) possible at each position, counting direction change, ± pre-set
function (setting a numerical value).
Application:
The reversal point is automatically determined by a 2-point inside or outside
measurement through oscillation, than a preset value can be simply assigned to it. During the
measurement. the measured ACTUAL value is saved by the MIN or MAX function and shown in
the display. In order to perform measuring movements with corresponding measuring accuracy,
64 measurement values are processed per second.
Note:
Suitable measuring inserts M2.5 are found on
Ç
4/49.
Lifting cap (Order No. 4246 0165,
Ç
4/54).
Eyelet rear wall (Order No. 4246 0175,
Ç
4/54).
Radio receiver (Order No. 4942 0030,
Ç
4/129).
Transmitter module for e-Stick (Order No. 4942 0040,
Ç
4/130).
Data cable RS 232 (Order No. 4942 0055,
Ç
4/130).
Data cable USB (Order No. 4942 0050,
Ç
4/130).
Data cable Digimatic (Order No. 4246 0185,
Ç
4/54).
Order
No.
Measurement range
mm
4246
Reading
mm
Housing ∅
mm
Accuracy
mm
With radio
transmission
0130
12.5
488.00
0.0005 60.5
0.004
–
0135
25.0
525.00
0.0005 60.5
0.004
•
(W488)
Digital dial gauge
Factory
standard
IP 42
Absolute
function
RS232
USB
Digimatic
Factory
standard
IP 42
Absolute
function
RS232
USB
Digimatic
m
m
Digital dial gauges
773