1313 / 1562
8/5
Articles marked ◊ are not held in stock, procurement is effected at short notice.
8
Abrasives
Design:
With ca. 48 single, set diamonds of ca. 3.5 carats in 4 rows, firmly embedded in the
working surface, with plastic handle.
Application:
Defining and honing aluminium oxide grinding wheels by hand. Suitable for dry use.
Order
No.
Abrasive surface
mm
8533
8536
Total length
mm
0005
40 x 10
92.20
92.20
220
(859)
(859)
Diamond grinding wheel dressing tool
8533
8536
8533
Diamond-studded head 180°
8536
Diamond-studded head 90°.
Design:
Shank mounted single- or one-stone abrasive diamond block, solid-shaped crystal with
few occlusions or irregular cracking, no crevices.
Application:
For profiling e.g. abrasives for all ceramic-bonded grinding wheels. The abrasive
is always clamped so that the angle to the middle of the grinding wheel is between 5° and 15°.
Dressing work with diamonds is better wet and with plenty of ventilation as they are sensitive to
shock and temperature. As the diamond becomes progressively blunt it should be twisted 90°.
Note:
The choice of the right diamond size depends on the ∅ of the grinding wheel, e.g. by the
disc width. Worn diamond abrasives should be regularly replaced.
Order
No.
Diamond size/
carat weight
8512
Design
For
grinding
wheel-∅ to
mm
0025
0.25
33.40
MK0
150
0050
0.50
58.40
MK0
300
0075
0.75
95.20
MK0
400
0100
1.00
138.00
MK0
500
1025
0.25
33.40
MK1
150
1050
0.50
58.40
MK1
300
1075
0.75
95.20
MK1
400
(859)
Order
No.
Diamond size/
carat weight
8512
Design
For
grinding
wheel-∅ to
mm
1100
1.00
138.00
MK1
500
1150
1.50
192.50
MK1
750
2025
0.25
33.40
*
Shank cyl. ∅ 8 x 80 mm 150
2050
0.50
58.40
*
Shank cyl. ∅ 8 x 80 mm 300
2075
0.75
95.20
*
Shank cyl. ∅ 8 x 80 mm 400
2100
1.00
138.00
*
Shank cyl. ∅ 8 x 80 mm 500
2150
1.50
192.50
*
Shank cyl. ∅ 8 x 80 mm 750
(859)
Diamond single-point dressing tool
* Other sizes available upon request.
Design:
5 diamonds, in a special sintered binding, so that they can be used right to the end
without changing.
Application:
The diamond-multi-point dressing tool is a practical smoothing tool for coarse
grinding with wheels of all diameters, up to 100 grit.
Note:
To prolong the life of this sharpener, continuous cooling should be used during the
dressing process.
Order
No.
Diamond content/carat weight ca.
8515
8518
8521
0005
1.00
107.50
107.50
107.50
*
(859)
(859)
(859)
Diamond-multi-point dressing tool
* Other sizes available upon request.
8515
8518
8521
8515
MK0. Total length 40 mm.
8518
MK1. Total length 57 mm.
8521
Shank cyl. ∅ 8 x 80 mm.
Design:
Single-sintered, high-concentrate (2.5 carat) diamond grain. Diamond cylinder set in
the shank (so no loss of diamonds), universal type.
Application:
Because of the multiple working points on an efficient diamond tool sharpener it
is only for straight-grinding wheelsurfaces (flat- and peripheral edge). These abrasives have no
gradient, so the whole of the diamond grit is employed. This type is not resettable, it is durable
and can be used until worn. Not suitable for detail work. For use with wheelgrit 36–120.
Note:
Adequate cooling before and during the smoothing process maximises its life span.
Order
No.
Diamond content/
carat weight ca.
8524
8527
8530
Diamond
inset ∅
mm
0005
2.50
63.90
63.90
63.90
*
8
(859)
(859)
(859)
Diamond multi-point dressing tool
* Other sizes available upon request.
8524
8527
8530
8524
MK0. Total length 40 mm.
8527
MK1. Total length 57 mm.
8530
From 1.5 carats with remote head
Shank cyl. ∅ 10 x 80 mm.
Grinding wheel dressers
Not all items are available in every country.
1313