129 / 1562
1/109
Articles marked ◊ are not held in stock, procurement is effected at short notice.
1
Cutting Tools
Design:
HSS-E PM, ASP2030
®
, DIN 335-C. 90° countersink angle. Axial and radial taper-ground
and CBN deep-ground, bright. With straight, u-shaped clamping slots and drilling spaces ground
from full pieces. Also provided with cutting and clearance angles for the most common materials.
Application:
Particularly suitable for the highest loads in INOX steel, stainless steel and Hardox.
Suitable for universal chatter and burr-free drilling, countersinking and deburring work for
countersunk screws DIN 963, DIN 964, DIN 965, DIN 966 and DIN 7991 in one step. Please
note the large countersink range! The excellent cutting properties and easy machining process
result from the cone-shaped back taper on the coat and angle of rake. The countersink achieves
the best results with the strongest feed and lowest cutting speed.
Note:
Sufficient supply of coolant is essential. HSS-E PM has, in comparison to conventional
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
1448
C
C
V
C
V
Order
No.
Nominal ∅
mm
1448
bright
Smallest ∅
mm
Total length
mm
Shank ∅
mm
0630
6.3
15.00
1.5
45
5
0830
8.3
17.20
2.0
50
6
1040
10.4
19.70
2.5
50
6
1240
12.4
25.50
2.8
56
8
1650
16.5
33.40
3.2
60
10
2050
20.5
45.30
3.5
63
10
2500
25.0
63.60
3.8
67
10
3100
31.0
98.10
4.2
71
12
4000
40.0
149.50
m
5.0
80
15
(134)
Countersinks and deburring countersinks 90° ASP
HSS-E
PM
DIN
335-C
Z
3
90°
bright
Set consisting of (order no. 1448).
Order
No.
Set contents
mm
1448
0005
6.3; 8.3; 10.4; 12.4; 16.5; 20.5
135.00
0010
6.3; 10.4; 16.5; 20.5; 25.0
173.50
(134)
Countersinks and deburring countersinks set 90° ASP
Design:
K20 carbide, DIN 335-C. 90° countersink angle. Axial and taper-ground and CBN deep-
ground. With straight, u-shaped clamping slots and drilling spaces ground from full pieces.
For tough materials such as Hardox 400/500, steels up to 60 HRC.
Application:
The excellent cutting properties and easy machining process result from the cone-
shaped back taper on the coat and angle of rake. The countersink achieves the best results with
the strongest feed and lowest cutting speed.
Note:
Sufficient supply of coolant is essential.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
1447
C
C
C
C
C
C
C
C
C
V
Order
No.
Nominal ∅
mm
1447
Smallest ∅
mm
Total length
mm
Shank ∅
mm
0630
6.3
73.30
2.2
45
5
0830
8.3
74.40
2.8
50
6
1040
10.4
76.10
3.5
50
6
1240
12.4
76.80
4.0
56
8
1650
16.5
89.10
5.0
60
10
2050
20.5
117.50
7.0
63
10
2500
25.0
158.50
9.0
67
10
3100
31.0
219.00
11.0
71
12
(136)
90° countersinks and deburring countersinks, carbide
With morse taper shank available on request.
Set consisting of (order no. 1447).
Order
No.
Set contents
mm
1447
0005
6.3; 8.3; 10.4; 12.4; 16.5; 20.5
436.00
0010
6.3; 10.4; 16.5; 20.5; 25.0
546.50
(136)
90° countersinks and deburring countersinks set, carbide
Carbide
DIN
335-C
Z
3
90°
HSS steels, a consistent, fine grained material
structure. This means they have good hot
hardness, pressure resistance and resistance
to wear.
Circle cutter and accessories
Not all items are available in every country.
129