778 / 1562
4/50
Lever gauges
DIN
2270
4250
4252
Design:
Housing protects the dovetail guides, chrome-plated, shockproof, bearing for lever
gauge shaft in precision ball bearings, movements bearing supported with rubies, automatic
switching of measuring direction, housing with three milled dovetail guides for holding the
clamping shaft (∅ 8 mm h6), measuring insert 1.6 with 2 mm ∅ carbide ball, rotating outer ring.
Supplied with key, in plastic case.
Application:
To check the concentricity of shafts and sleeves, for centring bore holes, alignment
of surfaces and parallelism inspections.
Order No.
0008 1033 1036 1040 1043 1046 1402 2031 2034 2047 3032 3045 3048
Measurement range
mm 0.8 0.5 0.2 0.8 0.5 0.2 2.0 0.8 0.5 0.2 0.8 0.5 0.2
4250
(422)
83.20
–
–
–
–
–
–
–
–
–
–
–
–
4252
(423)
–
105.55 91.75 78.00 107.75 93.95 125.55 98.60 111.85 110.95 100.90 118.20 113.00
Reading
mm 0.01 0.01 0.002 0.01 0.01 0.002 0.02 0.01 0.01 0.002 0.01 0.01 0.002
Scale numbering
mm 0–40–0 0–25–0 0–100–0 0–40–0 0–25–0 0–100–0 0–100–0 0–40–0 0–25–0 0–100–0 0–40–0 0–25–0 0–100–0
Housing ∅
mm 32 32 32 40 40 40 40 32 32 40 32 40 40
Probe length
mm 12.8 35.7 12.8 12.8 35.7 12.8 35.7 12.8 35.7 12.8 12.8 35.7 12.8
Shape
A
A
A
A
A
A
A
B
B
B
C
C
C
Precision lever gauge
Shape A =
Measuring insert pivots by 240° at right angle to scale.
Shape A =
Measuring insert pivots by 240° at right angle to scale.
Shape B =
Measuring insert pivots by 240° parallel to scale.
Shape C =
Measuring insert pivots by 240° to back of scale.
4252 shape A
4252
shape B
4252
shape C
4250
shape A
Design:
The measurement sensor is adjustable to the right and left by 110°,
the lever movement is switchable. Support on top and bottom clamping shaft (∅ 8 mm h6).
Supplied in plastic case.
Order
No.
Measurement
range mm
4255
Reading
mm
Scale numbering
Housing ∅
mm
Probe length
mm
0008
0.8
87.10
0.01
0–40–0
28
12
(422)
Lever gauge with pivoting measurement sensor
Design:
Metal housing, with revolving scale dial and patented shock absorber in the measuring
instrument. Two revolving clutch discs in the lifting system protect against overload.
Measurement in two directions possible due to automatic switching of the movement.
The consistent running direction of the pointer permits error-free reading; not sensitive to
magnetic fields, movement with 7 rubies. Ball bearing lever system with 240° pivot range
of measuring insert, very low measuring force.
Measuring force with measuring insert 12.53 mm: 0.15 N, with 36.53 mm: 0.06 N.
Monoblock housing with 3 milled dovetail rails. Supplied with measuring
insert M1.4 with ∅ 2 mm, a wrench for measuring insert and a clamping shaft ∅ 8 mm,
in plastic case.
Application:
Ideal for difference measurements, e.g. on the test plate, measurement of shape
and position deviations, in particular of concentricity and axial run-out.
Note:
Suitable measuring inserts M1.4 are found on
Ç
4/53.
Order
No.
Measurement
range mm
4251
Reading
mm
Housing ∅
mm
Measuring insert
mm
0005
0.8
113.00
0.01
28
12.5
0010
0.8
127.00
0.01
38
12.5
0015
0.5
147.00
0.01
28
36.5
0020
0.5
162.00
0.01
38
36.5
0007
0.2
133.00
m
0.002
28
12.5
0008
0.2
147.00
m
0.002
38
12.5
(495)
Lever gauge TESATAST
DIN
2270
Factory
standard
All stocked articles available within 24 hours by UPS Express.
All prices excluding VAT per piece (if not stated otherwise).
4
Measuring
Equipment
778