Catalog FORMAT plus 2017 - 2018 | Contact : 0799.402.346 | 0799.402.343 | e-mail : format@rocast.ro
Tap extractor/tap remover 249
Prețurile sunt orientative. Solicitați oferta și veți obține prețuri mult mai avantajoase.
Tap extractor set
Design: Supplied in a sturdy plastic cassette, incl. respective tap extractors and the right replacement finger sets.
1854
Number
Order No. 0010 0020 0030 0040
Design
Set contents
Cutting Tools 1
6-piece 10-piece 6-piece 10-piece
163.00 325.50 163.00 359.00
3-slot 3-slot 4-slot 4-slot
M4; 5; 6; 8; 10; 12
M3; 4; 5; 6; 8; 10; 12; 14; 16; 20
M4; 5; 6; 8; 10; 12
M 4; 5; 6; 8; 10; 12; 14; 16; 20; 22
(W178)
Tap borer
Design: Solid carbide, type N. The Tap borer has 3 blades. Application: Extraction must take place dry at ca. 1500–3500 rpm. With use of the right tap bore-out tool, the core of the tap is quickly bored out and the rest of the tap can be cleanly blown out of the drill hole. The workpiece must be clamped very steadily so that movement does not happen at higher speeds. A centring must be produced first by starting the tap bore-out tool up several times if the tap has broken off at an angle. Boring out can only be started now. Furthermore, the chips should be removed by "air blow" several times. A vibration can be felt just before the end of the bore-out process. The extractor should now be removed. The new thread can then be cut with a tap. Due to the high stresses caused by boring out, the cutting edges of the tap bore-out tool need to be resharpened from time to time.
Type N
Z 3
Solid carbide
DIN 6535-HA
1854
1854
∅ d 1
h10
∅ d 1
h10
Order No.
Thread
Total length L1 mm
Cutting edge length L2 mm
Order No.
Thread
Total length L1 mm
Cutting edge length L2 mm
mm
mm
0400 0500 0600 0800
3.3 37.60 4.2 39.90 5.0 44.10 6.8 59.50
M4 M5 M6 M8
50 50 50 60
15 15 15 20
1000 1200 1600 2000
8.5 75.00 10.2 92.20 14.0 157.00 17.5 275.50
M10 M12 M16 M20
70 75 100 100
25 30 40 50
(W176)
(W176)
Drilling paste
Design: Lubricant for metalwork. Drilling paste as hinge pin with 30 or 50 g contents. Application: For sheet spiral drill, stepped drill, countersink bits.
1312
1312
Drilling paste
Order No. 0005 0007
30g hinge pin 50g hinge pin
4.43
–
–
5.30
(W001,W124)
(W001,W124)
Cutting oil spray
Design: The cutting oil spray provides excellent separation and cooling effect. It increases the surface quality and tool life. Appllication: Especially suitable for drilling, turning, milling and thread cutting of hard and brittle materials.
1336
Contents ml
Order No. 0050 0420
50 420
3.15
6.50 (W001)
1/231
Articles marked ◊ are not held in stock, procurement is effected at short notice.
Made with FlippingBook Online document