TITAN FLOW CONTROL CATALOG - 0817

163 / 184

Tel: 910-735-0000 s Fax: 910-738-3848 s s
290 Corporate Drive s PO Box 7408 s Lumberton, NC 28358
YOUR PIPELINE TO THE FUTURE!
TITAN FLOW CONTROL, INC.
SWING CHECK VALVE f WAFERTYPE f SHORT PATTERN
ANSI CLASS 150 f CARBON STEEL & STAINLESS STEEL
MODELS: CV 12-CS
Body: Carbon Steel
Seat/Seal: Buna-N
CV 12-SS
Body: Stainless Steel
Seat/Seal: PTFE
T
TECHNICAL
®
TITAN
TITAN FLOW CONTROL, INC.
markets : oil and gas production, general industry, chemical , & petrochemical
service: this valve is intended for low flow service that is steady, clean ( no abrasives or solids ), and
non - pulsating. flow rate must not exceed for liquids : 15 ft /sec
ptfe properties : good for most chemical environments . offers excellent tear , abrasive , chemical , acid ,
and alkali resistance. not recommended for high pressure steam or large temperature variations .
buna- n properties: most widely used elastomer . good for most petroleum oils and fluids, silicone
greases and oils , and cold water. excellent compression set , tear , and abrasion resistance. poor weather
resistance and moderate heat resistance. not recommended for severe ozone- resistant applications .
The above data represents common market and service applications. No representation or guarantee, expressed or implied, is given due to the numerous variations
of concentrations, temperatures and flow conditions that may occur during actual service.
F
FEATURES
s robust des ign
th i s i s a s e l f -act i ng , non -r e turn , s i ngl e p lat e, wa f e r ty p e swi ng check
valv e wh i ch p rov i de s h i gh qual i ty and r e l i ab i l i ty wi th i n a s i mp l i f i ed
cons truct i on . ava i lab l e i n both carbon s t e e l and s ta i nl e s s s t e e l .
s minimal head loss
the low i ne rt i a d i sc i s de s i gned to op en and clos e unde r low
d i f f e r ent i al p r e s sur e cond i t i ons . al so, the short patt e rn de s i gn and
s tra i ght f low path m i n i m i ze p r e s sur e drop acros s the valv e .
s economi cal des ign
the low we i ght and short face -to -face d i mens i ons p rov i de an
econom i cal , s pace-s av i ng solut i on. add i t i onal ly, f lange ga s ke t s ar e
ty p i cal ly not r equ i r ed due to the bu i lt - i n, body s eal o- r i ngs .
s res i l i ent soft seats
sof t s eat s (p t f e or buna ) comb i ned wi th a grav i ty a s s i s t ed d i sc
he l p to ensur e a pos i t i v e shutof f wh i ch cr eat e s a bub b l e t i ght s eal
that me e t s or exce eds ap i 598 l eakage r equ i r ement s.
s versat i le des ign
th i s valv e can b e i ns tal l ed b e twe en we ld neck or s l i p - on ty p e
compan i on f lange s of d i f f e r ent s tandards. th i s valv e can not b e
i ns tal l ed i n a v e rt i cal p i p e l i ne wi th downward f low .
s fugi t i ve emi ss ion des ign
the one- p i ece body de s i gn e l i m i nat e s pot ent i al l eak paths to the
env i ronment so the r e ar e no body em i s s i ons.
PRESSURE/ TEMPERATURE RATING (1)
CS - ASTMA515 GR. 70 - CLASS 150
WOG (Non-shock): 285 PSI @ 100 °F
PRESSURE/ TEMPERATURE RATING (1)
SS - ASTMA240 GR. 316 - CLASS 150
WOG (Non-shock): 275 PSI @ 100 °F
SEAT AND BODY SEAL (O-RING) (1)
TEMPERATURE RANGE
PTFE: 14 ~ 320 °F
BUNA-N: -20 ~ 250 °F
S IZES : 2" ~ 24"
A
APPLICATIONS
1. The above listed temperatures are theoretical and
may vary during actual operating conditions.
CV12-1114