334 / 1562
2/88
All stocked articles available within 24 hours by UPS Express.
All prices excluding VAT per piece (if not stated otherwise).
2
Cutting Tools
Design:
Ultra-fine grit solid carbide, type NF, DIN 6527, 36°/38°,
TiAIN-coated,
with centre cut.
Cutting speed approx. 50 % higher than with non-coated tools.
Dry machining possible.
Application:
Can be used for rough milling, slot cutting and finishing
milling. The fine cord toothing produces small chips which are easy
to remove. This improves tool life and achieves a better surface finish.
The irregular spiral lead 36°/38° results in low-vibration running and
thus a very high surface quality. A much longer tool life is achieved
than with conventional tools.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
2392
95
100
90
60
115
130
Order
No.
dia.
d
1
= h10
mm
2392
TiAlN
Cutting edge length
l
2
mm
Overall length
l
1
mm
Neck ∅
d
3
mm
Clear area
l
3
mm
Shank dia.
d
2
= h6
mm
6WHHOV
XSWR
1PP
f
z
mm
0600
6
69.70
13
57
5.5
21
6
0.025
0800
8
84.50
19
63
7.5
27
8
0.032
1000
10
96.70
22
72
9.2
32
10
0.039
1200
12
116.00
26
83
11.2
38
12
0.048
1600
16
184.00
32
92
15.0
44
16
0.058
2000
20
280.50
38
104
19.0
54
20
0.073
(221)
Solid Carbide 4 Flute Rippa Cutter
Solid
carbide
UF
Type
NF
Z
4
DIN
6527
DIN
6535-HB
36°/38°
7°
Design:
Ultra-fine grit solid carbide, type NRf, DIN 6527, 30°,
fire-coated,
with centre cut.
Cutting speed approx. 50 % higher than with non-coated tools.
Dry machining possible.
With inner cooling: Increase in tool life of up to 50 %, since chip
blockage is reduced.
Application:
Can be used for rough milling. The fine cord toothing
produces small chips which are easy to remove. This improves tool life
and achieves a better surface finish.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
2391
95
100
30
60
115
130
Order
No.
dia.
d
1
= h10
mm
2391
Fire
Cutting edge length
l
2
mm
Overall length
l
1
mm
Shank dia.
d
2
= h6
mm
6WHHOV
XSWR
1PP
f
z
mm
0600
6
97.60
13
57
6
0.017
0800
8
106.50
19
63
8
0.024
1000
10
116.50
22
72
10
0.030
1200
12
142.00
26
83
12
0.036
1600
16
219.50
32
92
16
0.045
2000
20
326.00
38
104
20
0.057
(221)
Solid Carbide 4 Flute Rippa Cutter with Through Coolant
Fire
TiAlN
DIN
6527
Solid
carbide
UF
Type
NRf
Z
4
DIN
6535-HB
30°
9°
Milling Cutters
334