346 / 1562
2/100
All stocked articles available within 24 hours by UPS Express.
All prices excluding VAT per piece (if not stated otherwise).
2
Cutting Tools
Design:
Ultra-fine grit solid carbide, type N, according to company
standard, 30°,
Signum-coated,
with centre cut.
Cutting speed approx. 50 % higher than with non-coated tools.
Dry machining possible.
These tools should only be used in shrink or hydro-.expansion
chucks.
Application:
Can be used for copy milling. The neck chip channel
makes optimum tool range possible and thus makes it suitable for
mould-making applications. Suitable for machining hardened mate-
rials
up to 54 HRC
.
Note:
Copy milling; cutting values preferred at ap = 0.05 x d
1
and
ae = 0.1 x d
1
.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
2486
200
200
180
160
120
100
160
90
200
Order
No.
dia.
d
1
= h8
mm
2486
Signum
Radius
r ± 0.01
mm
Cutting edge length
l
2
mm
Overall
length l
1
mm
Neck ∅
d
3
mm
Clear area
l
3
mm
Angle of taper
in degrees
Shank dia.
d
2
= h6
mm
6WHHOV
XSWR
+5F
f
z
mm
0020
2
97.60
1.0
3.0
80
1.8
40
2.9
6
0.030
0030
3
69.70
1.5
3.5
80
2.8
40
2.2
6
0.040
0040
4
74.90
2.0
4.0
80
3.8
40
1.4
6
0.045
0060
6
90.60
3.0
6.0
100
5.6
60
1.0
8
0.050
0080
8
110.00
4.0
7.0
120
7.6
75
0.8
10
0.070
0100
10
146.50
5.0
8.0
120
9.6
70
0.8
12
0.100
0120
12
251.00
6.0
10.0
150
11.5
100
1.2
16
0.120
(221)
Solid Carbide 2 Flute Necked & Tapered Ball Nose Slot Drills
Signum
Design:
Ultra-fine grit solid carbide, type N, according to company
standard, 30°,
Signum-coated,
with centre cut.
Cutting speed approx. 50 % higher than with non-coated tools.
Dry machining possible.
These tools should only be used in shrink or hydro-.expansion
chucks.
Application:
Can be used for copy milling. The neck chip channel
makes optimum tool range possible and thus makes it suitable
for mould-making applications. Suitable for machining hardened
materials
up to 54 HRC
.
Note:
Copy milling; cutting values preferred at ap = 0.05 x d
1
and
ae = 0.1 x d
1
.
Shrunk-fit chucks can be found on
Ç
3/79.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
2488
200
200
180
160
120
100
160
90
200
Order
No.
dia.
d
1
= h8
mm
2488
Signum
Radius
r ± 0.01
mm
Cutting edge length
l
2
mm
Overall length
l
1
mm
Neck ∅
d
3
mm
Clear area
l
3
mm
Shank dia.
d
2
= h6
mm
6WHHOV
XSWR
+5F
f
z
mm
0060
6
61.90
3
6
80
1.8
45
6
0.050
0080
8
70.60
4
7
100
2.8
65
8
0.070
0100
10
116.50
5
8
120
3.8
80
10
0.100
0120
12
152.50
6
10
120
5.6
75
12
0.120
(221)
Solid Carbide Long Series 2 Flute Necked Ball Nose Slot Drills
Signum
Solid
carbide
UF
Type
N
Z
2
Factory
standard
DIN
6535-HA
30°
8°
Solid
carbide
UF
Type
N
Z
2
Factory
standard
DIN
6535-HA
30°
8°
Milling Cutters
346