1353 / 1618
8/5
Articles marked ◊ are not held in stock, procurement is effected at short notice.
Abrasives
8
Design:
With approx. 48 single, set diamonds
of approx. 3.5 carats in 4 rows, firmly
embedded in the working surface, with plastic
handle.
Application:
Defining and honing aluminium
oxide grinding wheels by hand. Suitable for
dry use.
Order
No.
Abrasive surface
mm
8533
8536
Total length
mm
0005
40 x 10
94.50
94.50
220
(W859)
(W859)
Diamond grinding wheel dressing tool
8533
8536
8533
Diamond-studded head 180°
8536
Diamond-studded head 90°.
Design:
Shaft mounted single- or one-stone
abrasive diamond block, solid-shaped crystal
with few occlusions or irregular cracking, no
crevices.
Application:
For profiling e.g. abrasives
for all ceramic-bonded grinding wheels.
The abrasive is always clamped so that the
angle to the middle of the grinding wheel
is between 5° and 15°. Dressing work with
diamonds is better wet and with plenty of
ventilation as they are sensitive to shock
and temperature. As the diamond becomes
progressively blunt it should be twisted 90°.
Note:
The choice of the right diamond size
depends on the ∅ of the grinding wheel, e.g.
the wheel width. Worn diamond abrasives
should be regularly replaced.
Order
No.
Diamond size/
carat weight
8512
Design
For grinding
wheel ∅ to
mm
0025
0.25 34.30
MK0
150
0050
0.50 60.10
MK0
300
0075
0.75 97.70
MK0
400
0100
1.00 141.50
MK0
500
1025
0.25 34.30
MK1
150
1050
0.50 60.10
MK1
300
1075
0.75 97.70
MK1
400
(W859)
Order
No.
Diamond size/
carat weight
8512
Design
For grinding
wheel ∅ to
mm
1100
1.00 141.50
MK1
500
1150
1.50 198.00
MK1
750
2025
0.25 34.30 *
Shaft cyl. ∅ 8 x 80 mm 150
2050
0.50 60.10 *
Shaft cyl. ∅ 8 x 80 mm 300
2075
0.75 97.70 *
Shaft cyl. ∅ 8 x 80 mm 400
2100
1.00 141.50 *
Shaft cyl. ∅ 8 x 80 mm 500
2150
1.50 198.00 *
Shaft cyl. ∅ 8 x 80 mm 750
(W859)
Diamond single point dressing tool
* Other sizes available upon request.
From 1.5 carats with remote head
Design:
5 diamonds, in a special sintered
binding, so that they can be used right to the
end without changing.
Application:
The diamond multi-point
dressing tool is a practical dressing tool for
coarse grinding with wheels of all diameters
up to 100 grit.
Note:
To prolong the life of this sharpener,
continuous cooling should be used during the
dressing process.
Order
No.
Diamond content/
carat weight approx.
8515
8518
8521
0005
1.00
107.50
107.50
107.50 *
(W859)
(W859)
(W859)
Diamond multi-point dressing tool
* Other sizes and shapes available upon request.
8515
8518
8521
8515
MK0. Total length 40 mm.
8518
MK1. Total length 57 mm.
8521
Shaft cyl. ∅ 8 x 80 mm.
Design:
Single-sintered, high-concentrate
(2.5 carat) diamond grain. Diamond cylinder
set in the shaft (so no loss of diamonds),
universal type.
Application:
Because of the multiple working
points on an efficient diamond tool sharpener,
it is only for straight grinding wheel surfaces
(flat and peripheral edge). These abrasives
have no gradient, so the whole of the
diamond grit is employed. This type is not
resettable, it is durable and can be used until
worn. Not suitable for detail work. For use
with disc wheel 36-120.
Note:
Adequate cooling before and during
the dressing process maximises its life span.
Order
No.
Diamond content/
carat weight approx.
8524
8527
8530
Diamond inset ∅
mm
0005
2.50
63.90
63.90
63.90 *
8
(W859)
(W859)
(W859)
Diamond multi-point dressing tool
* Other sizes and shapes available
upon request.
8524
8527
8530
8524
MK0. Total length 40 mm.
8527
MK1. Total length 57 mm.
8530
Shaft cyl. ∅ 10 x 80 mm.
Grinding wheel dressers
1353