321 / 1618
2/67
Articles marked ◊ are not held in stock, procurement is effected at short notice.
Cutting Tools
2
Design:
Ultra-fine grit solid carbide, type NH, DIN 6527, 40/42°,
fire-coated,
with centre cut.
Application:
Can be used for peripheral milling as well as for
universal machining.
For milling depths up to 2 x D.
Can also be
used for trimming and finishing milling. Can be used for rough
grinding, slot cutting and finishing milling. The irregular spiral lead
36°/38° results in particularly smooth running and thus very good
surface on the workpiece. A much longer tool life is achieved than
with conventional tools.
Order
No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al, Al and
Mg alloys
Copper,
brass,
bronze
2513
200
160
130
100
60
70
180
350
200
Order
No.
∅ d
1
h10
mm
2513
Fire
Cutting
length l
2
mm
Overall
length l
1
mm
Neck ∅
mm
Shank ∅
d
2
h6
mm
6WHHOV
XSWR
1PP
f
z
mm
0400
4 27.70
11
57 3.7 6 0.028
0500
5 27.70
13
57 4.7 6 0.028
0600
6 33.90
13
57 5.5 6 0.039
0800
8 46.80
19
63 7.5 8 0.053
(W221)
Order
No.
∅ d
1
h10
mm
2513
Fire
Cutting
length l
2
mm
Overall
length l
1
mm
Neck ∅
mm
Shank ∅
d
2
h6
mm
6WHHOV
XSWR
1PP
f
z
mm
1000
10 71.30
22
72 9.2 10 0.065
1200
12 90.80
26
83 11.2 12 0.079
1600
16 157.00
32
92 15.0 16 0.095
2000
20 243.50
38
104 19.0 20 0.110
(W221)
Solid Carbide Vari-Helix 4 Flute Endmill
Fire
Design:
Solid carbide (K10/K20), type N, according to factory
standard, with irregular pitch,
TiAIN-coated,
with centre cut.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible.
Application:
Can be used for peripheral milling and drill cutting.
The irregular pitch results in low-vibration running and thus a high
surface quality. Burr formation on the cutting edges is avoided.
Order
No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al, Al and
Mg alloys
Copper,
brass,
bronze
2459
140
140
130
80
100
160
2461
140
140
130
80
100
160
Order
No.
∅ d
1
h10
mm
2459
TiAlN
2461
TiAlN
Cutting length l
2
mm
Overall length l
1
mm
Shank ∅ d
2
h6
mm
6WHHOV
XSWR
1PP
f
z
mm
0300
3
18.40
18.40
8
57
6
0.005
0400
4
18.40
18.40
11
57
6
0.007
0500
5
18.40
18.40
13
57
6
0.010
0600
6
18.40
18.40
13
57
6
0.015
0800
8
26.10
26.10
19
63
8
0.025
1000
10
38.70
38.70
22
72
10
0.039
1200
12
49.80
49.80
26
83
12
0.047
1400
14
66.50
–
26
83
14
0.049
1600
16
86.70
86.70
32
92
16
0.053
1800
18
121.00
–
32
92
18
0.059
2000
20
134.00
134.00
38
104
20
0.065
(W212)
(W212)
Solid Carbide 4 Flute End Mill
2461
TiAlN
DIN
6535-HB
2459
TiAlN
DIN
6535-HA
Solid
carbide
Type
N
Z
4
Factory
standard
30°
Solid
carbide
Type
NH
Z
4
DIN
6527
DIN
6535-HA
36°/38°
O
O
G
G
G
Milling tools
321