322 / 1618
2/68
Cutting Tools
2
Design:
Ultra-fine grit solid carbide, type NH, DIN 6527, 40/42°,
fire-coated,
with centre cut.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible.
With inner cooling: Increase in tool life of up to 50%, since
chip blockage is reduced.
Application:
Can be used for peripheral milling as well as for
universal machining.
For milling depths up to 2 x D.
Can also be
used for trimming and finishing milling. Can be used for rough
grinding, slot cutting and finishing milling. The irregular spiral lead
40°/42° results in particularly smooth running and thus very good
surface on the workpiece. A much longer tool life is achieved than
with conventional tools.
Order
No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al, Al and
Mg alloys
Copper,
brass,
bronze
2454
170
170
140
70
70
200
130
Order
No.
∅ d
1
h10
mm
2454
Fire
Cutting
length l
2
mm
Overall
length l
1
mm
Neck ∅
mm
Shank ∅
d
2
h6
mm
6WHHOV
XSWR
1PP
f
z
mm
0600
6 65.80
13
57 5.5 6 0.039
0800
8 86.40
19
63 7.5 8 0.053
1000
10 128.50
22
72 9.2 10 0.065
(W221)
Order
No.
∅ d
1
h10
mm
2454
Fire
Cutting
length l
2
mm
Overall
length l
1
mm
Neck ∅
mm
Shank ∅
d
2
h6
mm
6WHHOV
XSWR
1PP
f
z
mm
1200
12 164.50
26
83 11.2 12 0.079
1600
16 285.00
32
92 15.0 16 0.095
2000
20 436.50
38
104 19.0 20 0.110
(W221)
Solid Carbide Vari-Helix 4 Flute End Mill with Through Coolant
Fire
Design:
Ultra-fine grit solid carbide, type N, DIN 6527, 35°/38°, with
centre cut.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible. Air cooling recommended.
Application:
Can be used for peripheral milling as well as for universal
machining.
For milling depths up to 2 x D.
Can also be used for
trimming and finishing milling. Can be used for rough grinding, slot
cutting and finishing milling. The irregular spiral lead 35°/38° results
in particularly smooth running and thus very good surface on the
workpiece. A much longer tool life is achieved than with conventional
tools, as well as maximum stability during machining. In addition,
feeds higher by up to 60% can be realized.
Order
No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al, Al and
Mg alloys
Copper,
brass,
bronze
2483
180
160
120
80
60
100
300
80
2448
200
180
160
130
100
70
200
Order
No.
∅ d
1
h10
mm
2483
TiAlN
2448
Fire
Cutting length l
2
mm
Overall length l
1
mm
Shank ∅ d
2
h6
mm
6WHHOV
XSWR
1PP
f
z
mm
0600
6
22.40
26.40
13
57
6
0.039
0800
8
30.90
37.30
19
63
8
0.053
1000
10
45.40
55.90
22
72
10
0.065
1200
12
57.60
71.40
26
83
12
0.079
1400
14
77.90
95.20
26
83
14
0.095
1600
16
101.50
124.00
32
92
16
0.095
1800
18
139.50
174.00
32
92
18
0.110
2000
20
154.50
192.50
38
104
20
0.110
(W212)
(W220)
Solid carbide end mill with 35°/38° spiral lead
2448
Fire
DIN
6535-HA
2483
TiAlN
DIN
6535-HB
Solid
carbide
Type
NH
Z
4
DIN
6527
DIN
6535-HB
40°/42°
Solid
carbide
Type
N
Z
4
DIN
6527
35°/38°
O
O
G
G
O
G
Milling tools
322