333 / 1618
2/79
Articles marked ◊ are not held in stock, procurement is effected at short notice.
Cutting Tools
2
Order
No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al, Al and
Mg alloys
Copper,
brass,
bronze
2397
150
150
130
100
70
Order
No.
∅ d
1
h10
mm
2397
TiAlN
Cutting length l
2
mm
Overall length l
1
mm
Shank ∅ d
2
h6
mm
Number of teeth
f
z
mm
0600
6
37.80
16
57
6
3
0.021
0800
8
44.20
16
63
8
3
0.028
1000
10
65.90
22
72
10
4
0.026
1200
12
84.70
26
83
12
4
0.032
1600
16
138.00
32
92
16
4
0.038
2000
20
222.00
38
104
20
4
0.033
(W212)
Solid carbide Rippa Cutter
TiAlN
Design:
Ultra-fine grit solid carbide, type NF, DIN 6527, 36/38°,
TiAIN-coated,
with centre cut.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible.
Application:
Can be used for rough milling, slot cutting and finishing
milling. The fine cord toothing produces small chips which are easy
to remove. This improves tool life and achieves a better surface
finish. The irregular spiral lead 36°/38° results in low-vibration
running and thus a very high surface quality. A much longer tool life
is achieved than with conventional tools.
Order
No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al, Al and
Mg alloys
Copper,
brass,
bronze
2392
150
150
130
80
60
150
130
Order
No.
∅ d
1
h10
mm
2392
TiAlN
Cutting length l
2
mm
Overall length l
1
mm
Neck ∅ d
3
mm
Clear area l
3
mm
Shank ∅ d
2
h6
mm
6WHHOV
XSWR
1PP
f
z
mm
0600
6
74.10
13
57
5.5
21
6
0.025
0800
8
89.80
19
63
7.5
27
8
0.032
1000
10
103.00
22
72
9.2
32
10
0.039
1200
12
122.50
26
83
11.2
38
12
0.048
1600
16
194.00
32
92
15.0
44
16
0.058
2000
20
298.00
38
104
19.0
54
20
0.073
(W221)
Solid Carbide 4 Flute Rippa Cutter
TiAlN
Design:
Ultra-fine grit solid carbide, type H, according to factory
standard, 30°,
TiAlN-coated.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible.
Application:
Can be used for rough milling. The fine cord toothing
produces small chips which are easy to remove. This improves tool
life and achieves a better surface finish. Particularly suitable for
VA machining
.
Solid
carbide
Type
INOX
Z
3–5
Factory
standard
DIN
6535-HB
30°
Solid
carbide
Type
NF
Z
4
DIN
6527
DIN
6535-HB
36°/38°
Milling Cutters
333