335 / 1618
2/81
Articles marked ◊ are not held in stock, procurement is effected at short notice.
Cutting Tools
2
Design:
Ultra-fine grit solid carbide, type NRf, DIN 6527, 30°,
fire-coated,
with centre cut.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible.
With inner cooling: Increase in tool life of up to 50%,
since chip blockage is reduced.
Application:
Can be used for rough milling. The fine cord toothing
produces small chips which are easy to remove. This improves tool
life and achieves a better surface finish.
Order
No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al, Al and
Mg alloys
Copper,
brass,
bronze
2391
150
150
30
80
60
115
130
Order
No.
∅ d
1
h10
mm
2391
Fire
Cutting length l
2
mm
Overall length l
1
mm
Shank ∅ d
2
h6
mm
6WHHOV
XSWR
1PP
f
z
mm
0600
6
104.00
13
57
6
0.017
0800
8
113.00
19
63
8
0.024
1000
10
123.50
22
72
10
0.030
1200
12
150.50
26
83
12
0.036
1600
16
232.00
32
92
16
0.045
2000
20
346.00
38
104
20
0.057
(W221)
Solid Carbide 4 Flute Rippa Cutter with Through Coolant
Fire
Design:
Ultra-fine grit solid carbide, type HR, according to factory
standard, 45°,
TiAlN-coated,
with centre cut.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible.
Application:
Can be used for rough milling. The fine cord toothing
produces small chips which are easy to remove. This improves tool
life and achieves a better surface finish. Particularly suitable for
machining stainless steel
.
Order
No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al, Al and
Mg alloys
Copper,
brass,
bronze
2398
338
338
252
170
170
Order
No.
∅ d
1
h10
mm
2398
TiAlN
Cutting
length l
2
mm
Overall
length l
1
mm
Shank ∅
d
2
h6
mm
Number
of teeth f
z
mm
0600
6 35.90
7
54
6
4 0.016
0800
8 42.00
9
58
8
4 0.021
1000
10 62.70
14
66
10
4 0.026
(W212)
Order
No.
∅ d
1
h10
mm
2398
TiAlN
Cutting
length l
2
mm
Overall
length l
1
mm
Shank ∅
d
2
h6
mm
Number
of teeth f
z
mm
1200
12 80.60
16
73
12
4 0.032
1600
16 131.00
22
82
16
5 0.030
2000
20 211.00
26
92
20
6 0.022
(W212)
Solid Carbide Stub Multi-Flute Rippa Cutter
TiAlN
Solid
carbide
Type
NRf
Z
4
DIN
6527
DIN
6535-HB
30°
Solid
carbide
Type
HR
Z
4–6
Factory
standard
DIN
6535-HB
45°
Milling Cutters
335