149 / 1562
1/129
Articles marked ◊ are not held in stock, procurement is effected at short notice.
1
Cutting Tools
Design:
HSS, DIN 859, form B, with cylinder shank and square drive.
The uneven tooth pitch ensure chatter-free and accurate drilling. The body of the reamer is
slotted, the nominal ∅ can be increased to approx. 1/100 by turning the head screw in.
The setting should be made using a ring gauge (order no. 4411). All required adaptations
can be set and wear compensated. Reamers are set to the nominal size.
Store depressurised.
The ∅ 4 and 5 mm are straight fluted, spiral fluted from ∅ 6 mm (left spiral 7°).
Application:
Perfectly suited for single production or repair work, only for reaming through-
holes. Not suitable for machining blind holes due to the conical point geometry and head screw.
Also suitable for holes with interrupted cut. Particularly suitable for steel materials up to
500 N/mm
2
in strength e.g. general construction steels, steel materials up to 900 N/mm
2
in
strength such as machine steels, tempered steels, tool steels, case-hardening steels, casting
materials and non-ferrous metals such as aluminium, brass, copper and bronzes.
Note:
The hand reamer is sensitive to impacts and chips should therefore not be knocked out,
but blown or washed out. Tap wrenches for manual actuation see page
Ç
1/220.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
1504
C
V
V
V
V
Order
No.
Nominal
∅ d
1
mm
1504
bright
Overall
length l
1
mm
Cutting edge
length l
2
mm
Shank
∅ d
2
mm
0400
4.0*
50.80
76
24
4
0500
5.0*
51.20
87
30
5
0600
6.0
51.20
93
33
6
0700
7.0
62.80
107
38
7
0800
8.0
61.80
115
42
8
0900
9.0
66.40
124
46
9
1000
10.0
67.60
133
50
10
1100
11.0
81.50
142
51
11
1200
12.0
76.70
152
56
12
1300
13.0
89.60
152
56
13
(141)
Order
No.
Nominal
∅ d
1
mm
1504
bright
Overall
length l
1
mm
Cutting edge
length l
2
mm
Shank
∅ d
2
mm
1400
14.0
92.10
163
61
14
1500
15.0
94.30
163
61
15
1600
16.0
117.50
175
67
16
1800
18.0
123.50
188
68
18
1900
19.0
126.50
188
68
19
2000
20.0
130.00
201
75
20
2200
22.0
156.00
215
82
22
2400
24.0
171.00
231
85
24
2500
25.0
171.00
231
85
25
3000
30.0
222.00
247
94
30
(141)
Hand reamer, adjustable
m
Limit plug gauge
for testing drilled holes
is found on
Ç
4/67.
bright
ø
ø
ø
ø
bright
HSS
DIN
859
Form
B
approx. 7°
* Straight fluted
Reamers
Not all items are available in every country.
149