150 / 1562
1/130
All stocked articles available within 24 hours by UPS Express.
All prices excluding VAT per piece (if not stated otherwise).
1
Cutting Tools
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
1505
C
V
V
V
V
Order
No.
Nominal ∅ d
1
mm
1505
bright
Adjustment
range ∅
mm
Overall
length l
1
mm
Cutting edge
length l
2
mm
Width
of keys
mm
Number of
blades
0100
6.4
69.90
6.4– 7.2
110
32
3.0
4
0105
7.2
69.90
7.2– 8.0
110
32
3.4
4
0110
8.0
69.90
8.0– 9.0
115
34
3.8
5
0115
9.0
73.40
39.0–10.0
115
34
4.3
5
0120
10.0
73.40
10.0–11.0
115
34
4.9
5
0125
11.0
73.40
11.0–12.0
125
35
4.9
5
0130
12.0
82.50
12.0–13.5
135
41
6.2
5
0135
13.5
93.10
13.5–15.5
146
50
7.0
5
0140
15.5
95.40
15.5–18.0
166
60
8.0
5
0145
18.0
103.50
18.0–21.0
178
65
9.0
5
0150
21.0
124.50
21.0–24.0
195
76
11.0
5
0155
24.0
131.50
24.0–27.5
218
82
12.0
5
0160
27.5
161.50
27.5–31.5
245
86
14.5
5
0165
31.5
225.50
31.5–37.0
280
98
18.0
6
0170
37.0
292.00
37.0–45.0
325
108
20.0
6
0175
45.0
395.00
45.0–55.0
370
118
26.0
6
(141)
Hand reamer, quick adjustment
bright
Design:
Right cutting, with replaceable blades made of HSS, factory standard and cylinder
shank with square drive. The uneven blade pitch ensure chatter-free and accurate drilling.
The reamer can be progressively set within the stated adjustment range. The setting should
be made using a ring gauge (order no. 4411). Bright surface
Application:
Particularly suitable for repair work. Only for reaming through-holes. Not suitable
for machining blind holes due to the head screw. Particularly suitable for steel materials up to
500 N/mm
2
in strength e.g. general construction steels, steel materials up to 900 N/mm
2
in
strength such as machine steels, tempered steels, tool steels, case-hardening steels, casting
materials and non-ferrous metals such as aluminium, brass, copper and bronzes.
Note:
Tap wrenches for manual actuation – see
Ç
1/220.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
1508
C
C
V
V
V
V
V
U
U
U
Order
No.
Nominal ∅
mm
1508
bright
Small/large ∅
mm
Cutting length
mm
Total length
mm
Width of keys
mm
0300
3
18.85
2.90/ 4.06
58
80
3.0
0400
4
21.40
3.90/ 5.26
68
93
3.8
0500
5
22.50
4.90/ 6.36
73
100
4.9
0600
6
27.20
5.90/ 8.00
105
135
6.2
0800
8
42.10
7.90/10.80
145
180
8.0
1000
10
59.50
9.90/13.40
175
215
10.0
1200
12
75.70
11.80/16.00
210
255
11.0
1300
13
88.10
12.80/17.00
210
255
12.0
1400
14
93.10
13.80/18.00
210
255
12.0
1600
16
105.00
15.80/20.40
230
280
14.5
2000
20
136.50
19.80/24.80
250
310
18.0
(140)
Hand cone reamer
Design:
HSS, DIN 9-B with left spiral approx. 7°. The uneven tooth pitch ensure chatter-free
and accurate drilling. With cylinder shank with square drive. Bright surface
Application:
For reaming conical holes for taper pins according to DIN 1, DIN 258, DIN 1447,
DIN 7977 and DIN 7978. Perfectly suited for single production or repair work. Also suitable
for holes with interrupted cut. Pre-drill with a cylindrical spiral drill or pin drill.
Particularly suitable for steels up to 500 N/mm
2
in strength such as non-ferrous metals,
plastics, steels up to 1000 N/mm
2
amd casting materials.
Note:
Tap wrenches for manual actuation – see
Ç
1/220.
bright
HSS
Factory
standard
HSS
DIN
9-B
approx. 7°
1:50
Reamers
150