353 / 1562
2/107
Articles marked ◊ are not held in stock, procurement is effected at short notice.
2
Cutting Tools
Design:
Solid carbide
NANO,
type H, according to company
standard, 30°,
TiAlN-S-coated,
with centre cut.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible.
Application:
Can be used for peripheral milling and slot cutting.
Is also suitable for milling deep grooves thanks to the
offset shaft. With corner radius to avoid notching effects
on the workpiece. Less corner wear during slot
cutting. Suitable for HSC machining
up to 70 HRC
.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
2494
195
195
195
130
130
130
Order
No.
dia.
d
1
mm
2494
TiAlN-S
Corner radius
r
mm
Cutting edge
length l
2
mm
Overall length
l
1
mm
Neck dia.
d
3
mm
Clear area
l
3
mm
Shank dia.
d
2
= h6
mm
+DUG
PDFKLQLQJ
RYHU
+5F
f
z
mm
0101
1.0
22.00
0.1
1.5
40
–
–
3
0.002
0100
1.0
32.30
0.1
1.5
40
–
–
6
0.002
0151
1.5
22.00
0.1
2.2
40
–
–
3
0.002
0150
1.5
32.30
0.1
2.2
40
–
–
6
0.002
0201
2.0
19.95
0.1
3.0
40
1.95
6
3
0.004
0200
2.0
29.20
0.1
3.0
40
1.95
6
6
0.004
0250
2.5
29.20
0.1
4.0
40
2.40
6
6
0.005
0300
3.0
29.20
0.1
4.0
45
2.85
7
6
0.006
0350
3.5
29.20
0.1
5.0
45
3.35
9
6
0.007
0400
4.0
29.20
0.1
5.0
45
3.85
9
6
0.008
0500
5.0
29.20
0.2
6.0
50
4.85
11
6
0.011
0600
6.0
29.20
0.2
7.0
50
5.85
14
6
0.013
0800
8.0
37.00
0.2
9.0
60
7.70
18
8
0.016
1000
10.0
55.40
0.2
12.0
75
9.70
25
10
0.019
1200
12.0
76.50
0.3
15.0
75
11.70
30
12
0.022
1600
16.0
127.50
0.3
18.0
90
15.70
38
16
0.026
(212)
Solid Carbide 4 Flute End Mill with Corner Radius for Hard Machining
TiAlN-S
Design:
Ultra-fine grit solid carbide, type N, according to
company standard, 30°,
TiAlN-coated,
with centre cut.
Cutting speed approx. 50% higher than with non-coated
tools. Dry machining possible.
Application:
Can be used for peripheral milling. With corner
radius to avoid notching effects on the workpiece. Suitable for
HSC machining
up to 62 HRC
.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
2436
133
133
82
82
82
55
50
25
Order
No.
dia.
d
1
mm
2436
TiAlN
Corner radius
r
mm
Cutting edge
length l
2
mm
Overall length
l
1
mm
Neck dia.
d
3
mm
Clear area
l
3
mm
Shank dia.
d
2
= h6
mm
6WHHOV
XSWR
+5F
f
z
mm
0200
2.0
29.00
0.20
2.5
50
1.9
5
6
0.002
0250
2.5
29.00
0.25
3.0
50
2.4
6
6
0.003
0300
3.0
29.00
0.30
4.0
50
2.8
7
6
0.003
0350
3.5
29.00
0.35
4.5
50
3.2
8
6
0.004
0400
4.0
29.00
0.40
5.0
50
3.7
9
6
0.004
0500
5.0
29.00
0.50
6.0
50
4.6
12
6
0.005
0600
6.0
29.00
0.60
7.0
55
5.6
14
6
0.006
0800
8.0
37.10
0.80
10.0
60
7.4
18
8
0.008
1000
10.0
54.90
1.00
12.0
70
9.4
25
10
0.009
1200
12.0
75.30
1.20
15.0
80
11.4
30
12
0.010
(212)
Solid Carbide 4 Flute End Mill with Corner Radius for Hard Machining
TiAlN
Solid
carbide
NANO
Type
H
Z
4
Factory
standard
DIN
6535-HA
30°
7°
HSC
Solid
carbide
UF
Type
N
Z
4
Factory
standard
DIN
6535-HA
30°
7°
HSC
Milling Cutters
Not all items are available in every country.
353