357 / 1562
2/111
Articles marked ◊ are not held in stock, procurement is effected at short notice.
2
Cutting Tools
Design:
Solid carbide
NANO,
type H, according to company standard,
45°,
TiAlN-S-coated,
with centre cut.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible.
Application:
Can be used for slot cutting. Is also suitable for milling
deep grooves thanks to the offset shaft.
For large milling depths
of up to 3 x D.
With corner radius to avoid notching effects on the
workpiece – less corner wear during plunge cutting and slot cutting.
The 45° spiral results in a soft and peeling cut and thus a high surface
quality. Burr formation on the cutting edges is avoided. Suitable for
HSC machining
up to 70 HRC
.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
2438
490
490
490
301
301
301
Order
No.
dia.
d
1
mm
2438
TiAlN-S
Corner radius
r
mm
Cutting edge
length l
2
mm
Overall length
l
1
mm
Neck dia.
d
3
mm
Clear area
l
3
mm
Shank dia.
d
2
= h6
mm
+DUG
PDFKLQLQJ
RYHU
+5F
fz
mm
0010
6
39.20
0.5
6
50
5.85
14
6
0.022
0020
6
44.60
0.5
13
70
–
–
6
0.022
0030
6
53.70
0.5
26
70
–
–
6
0.022
0040
8
46.80
0.5
8
60
7.70
24
8
0.028
0050
8
55.90
0.5
19
90
–
–
8
0.028
0060
8
69.40
0.5
36
90
–
–
8
0.028
0070
10
73.10
1.0
10
70
9.70
30
10
0.031
0080
10
84.30
0.5
22
100
–
–
10
0.031
0090
10
84.30
1.0
22
100
–
–
10
0.031
0100
10
109.50
1.0
46
100
–
–
10
0.031
0110
12
115.00
0.5
26
110
–
–
12
0.033
0120
12
87.30
1.0
12
75
11.70
30
12
0.033
0130
12
115.00
1.0
26
110
–
–
12
0.033
0140
12
155.50
1.0
56
110
–
–
12
0.033
0150
16
194.00
1.0
32
130
–
–
16
0.035
0160
16
212.00
1.5
32
130
–
–
16
0.035
0170
16
272.50
1.5
66
130
–
–
16
0.035
0180
20
284.50
1.0
38
140
–
–
20
0.036
0190
20
310.50
1.5
38
140
–
–
20
0.036
0200
20
310.50
2.0
38
140
–
–
20
0.036
0210
20
425.00
2.0
76
140
–
–
20
0.036
(212)
Solid Carbide Multi Flute Necked End Mill with Corner Radius for Hard Machining
TiAlN-S
Design:
Ultra-fine grit solid carbide (K50), type H, according to
company standard, 55°,
Signum-coated,
with centre cut.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible.
Application:
Can be used for peripheral milling, trimming and
high-precision finishing.
For large milling depths up to 3 x D.
Ideal for use in mould-making and dip working thanks to the neck chip
channel and corner radius with long range. The extremely high spiral
lead and reinforced core results in particularly smooth running and thus
low deviation in shape and a very good surface on the workpiece.
uitable for HSC machining
up to 62 HRC
.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
2388
55
45
40
40
200
Order
No.
dia.
d
1
= h10
mm
2388
Signum
Corner radius
r
mm
Cutting edge
length l
2
mm
Overall length
l
1
mm
Neck dia.
d
3
mm
Clear area
l
3
mm
Shank dia.
d
2
= h6
mm
6WHHOV
XSWR
+5F
f
z
mm
0600
6
40.90
0.5
13
75
5.7
39
6
0.024
0800
8
46.20
0.5
19
100
7.7
64
8
0.032
1000
10
81.90
0.5
22
100
9.5
60
10
0.038
1200
12
114.00
1.0
26
150
11.5
105
12
0.046
1600
16
204.00
1.0
32
150
15.5
102
16
0.054
(221)
Solid Carbide Long Series Multi Flute Necked End Mill with Corner Radius for Hard Machining
Signum
Solid
carbide
NANO
Type
H
Z
6
Factory
standard
DIN
6535-HA
45°
1°
HSC
Solid
carbide
UF
Type
H
Z
6
Factory
standard
DIN
6535-HA
55°
–5°bis–10°
HSC
Milling Cutters
Not all items are available in every country.
357