352 / 1562
2/106
All stocked articles available within 24 hours by UPS Express.
All prices excluding VAT per piece (if not stated otherwise).
2
Cutting Tools
Design:
Ultra-fine grit solid carbide, type N, according to company
standard, 30°,
TiAlN-coated,
with centre cut.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible.
Application:
Can be used for milling keyways and feather key
grooves. With corner radius to avoid notching effects on the
workpiece. Suitable for HSC machining
up to 62 HRC
.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
2428
80
80
52
52
52
32
32
32
Order
No.
dia. d
1
= e8
mm
2428
TiAlN
Corner
radius r
mm
Cutting edge
length l
2
mm
Overall
length l
1
mm
Shank dia.
d
2
= h6
mm
6WHHOV
XSWR
+5F
f
z
mm
1030
3
34.80
0.3
12
50
6 0.003
1040
4
34.80
0.3
15
50
6 0.004
1042
4
34.80
0.5
15
50
6 0.004
1050
5
34.80
0.3
20
60
6 0.006
1052
5
34.80
0.5
20
60
6 0.006
1060
6
34.80
0.3
20
60
6 0.010
1062
6
34.80
0.5
20
60
6 0.010
1064
6
34.80
1.0
20
60
6 0.010
1080
8
44.60
0.3
25
70
8 0.014
1082
8
44.60
0.5
25
70
8 0.014
1084
8
44.60
1.0
25
70
8 0.014
(212)
Order
No.
dia. d
1
= e8
mm
2428
TiAlN
Corner
radius r
mm
Cutting edge
length l
2
mm
Overall
length l
1
mm
Shank dia.
d
2
= h6
mm
6WHHOV
XSWR
+5F
f
z
mm
1086
8
48.60
1.5
25
70
8 0.014
1088
8
48.60
2.0
25
70
8 0.014
1100
10
65.90
0.3
30
90
10 0.017
1102
10
65.90
0.5
30
90
10 0.017
1104
10
65.90
1.0
30
90
10 0.017
1106
10
71.90
1.5
30
90
10 0.017
1108
10
71.90
2.0
30
90
10 0.017
1202
12
90.40
0.5
30
90
12 0.015
1204
12
90.40
1.0
30
90
12 0.015
1206
12
98.70
1.5
30
90
12 0.015
1208
12
98.70
2.0
30
90
12 0.015
(212)
Solid Carbide 2 Flute Slot Drill with Corner Radius for Hard Machining
TiAlN
Design:
Solid carbide (K05/10), type N, DIN 6527, 30°,
Signum-coated,
with tapered neck – see dimension l
3
/l
4
(clear area) and centre cut.
Cutting speed approx. 50% higher than with non-coated tools.
Dry machining possible.
These tools should only be used in shrink or hydro-.expansion
chucks.
Application:
Can be used for copy milling, traverse and slot cutting.
The tool life increases with MQL or air cooling. Suitable for HSC machining
up to 56 HRC
.
Note:
Copy milling; cutting values preferred at ap = 0.1 x d
1
and ae = 0.5 x d
1
.
Order No.
Steels
up to
850
N/mm
2
Steels
up to
1000
N/mm
2
Steels
up to
1400
N/mm
2
Steels
up to
42 HRC
Steels
up to
52 HRC
Steels
up to
56 HRC
Steels
up to
60 HRC
Hard
machining
over
60 HRC
Stainless
and acid-
resistant
steels (INOX)
Ti steels,
Ti alloys,
special
steels
Cast iron
materials
Al,
AI and
Mg alloys
Copper,
brass,
bronze
2432
200
200
180
160
140
80
120
80
200
Order
No.
dia.
d
1
= h8
mm
2432
Signum
Corner radius
r ± 0.01
mm
Cutting edge
length l
2
mm
Overall length
l
1
mm
Neck dia.
d
3
mm
Clear area
l
3
mm
Clear area
l
4
mm
Shank dia.
d
2
= h6
mm
6WHHOV
XSWR
+5F
f
z
mm
0200
2
101.00
0.5
3.0
80
1.8
8
40
6
0.02
0300
3
88.90
0.5
3.5
80
2.8
12
40
6
0.03
0400
4
61.90
1.0
4.0
80
3.8
20
40
6
0.035
0600
6
92.30
2.0
6.0
80
5.6
25
60
8
0.04
0800
8
119.50
2.0
7.0
100
7.6
30
75
10
0.05
1000
10
140.50
3.0
8.0
120
9.6
30
70
12
0.07
1200
12
235.00
4.0
10.0
160
11.5
30
100
16
0.08
(221)
Solid Carbide 2 Flute Necked and Tapered Torus Cutter with Corner Radius for Hard Machining
Signum
Solid
carbide
UF
Type
N
Z
2
Factory
standard
DIN
6535-HA
30°
7°
HSC
Solid
carbide
Type
N
Z
2
DIN
6527
DIN
6535-HA
30°
8°
HSC
Milling Cutters
352